Archer NX200 aggregation (CA)

Archer NX200 aggregation (CA)

Archer NX200 aggregation (CA)
Archer NX200 aggregation (CA)
2024-09-27 18:30:25 - last edited 2024-10-10 08:08:12
Model: Archer NX200  
Hardware Version: V1
Firmware Version:

Dear users and technical specialists, 

I would like to ask if this router - Archer NX200 - can aggregate  (combine) 5G and 4G together... or it can work only in either 5G or 4G. 

 

I need to know if this 5G router is able to combine these specific frequencies :  5G (N28) + 4G (B1, B3 and B20)

 

thank you in advance,

Jimmydix

  0      
  0      
#1
Options
4 Reply
Re:Archer NX200 aggregation (CA)
2024-09-29 07:58:35

  @Jimmydix 

Hi,

Thanks for posting on TP-Link Community.

 

Archer NX200 can combine 5G and 4G.

It may work to combine 5G (N28) + 4G (B1, B3 and B20) but it does not allow to control it manually. It also depends on the SIM provider.

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Archer NX200 aggregation (CA)
2024-09-29 15:56:12

  @Sunshine 

 

Dear Sunshine, 

thank you very much for your confirmation. If this archer NX200 can really merge 5G and 4G together then I would be a happy customer. 

 

Sim card that I will be using in the modem has speed limited to 150 Mbps (the limit is somewhat flexible so it can go +15% faster) so combining 5G (N28 gives me around 40-60Mbps) and 4G together (B1+B20 gives me 50-90 Mbps)  would optimaly utilize the sim card´s tariff   

 

Currently the BTS tower servicing my location has 5G (N28) and 4G in B1, B3 and B20 variant. 

 

I guess my other question would be : How many frequencies can Archer nx200 combine together ? I found out it has 8 antennas 2x2 mimo (I dont know how many antennas are 5G and how many 4G) so it can combine 4 channels together? 

Archer Nx200 has also externall antenna slots which I would use with external antenna - I also dont know if those externall antenna slots support low frequencies (in my case 700-2100) 

 

I was testing my expensive Zyxel nr7101 there which I took for testing from another property and it was able to aggregate 3 frequencies: N28 + B1+B20.  B3 signal was propably too weak so the modem choosed B20 instead. 

 

Thank you for more clarification on this. 

Jimmy

 

 

  0  
  0  
#3
Options
Re:Archer NX200 aggregation (CA)
Wednesday

  @Jimmydix 

I think NX200 utilising Mediatek T750, spec says LTE 5x and 5G 2x

  0  
  0  
#4
Options
Re:Archer NX200 aggregation (CA)
21 hours ago - last edited 21 hours ago

Hello @Sunshine,

can you also please confirm if the device is able to use the carrier aggregarion between different bands over 4G GSM net? I'd like to use it with a SIM that does not support 5G. I'm a very very happy user of Archer MR600...that is a Cat6 carrier aggregator (max 2 possible bands for CA). I'd not have asked here if this info there had been present in the Mr600 VS NX200 comparions chart:

Left: MR600 - Right NX200. Source: TP-Link Italy

André
  0  
  0  
#5
Options