Solution India Jio SIM stops working on TP-Link LTE Gateway Routers after upgrading to 5G
This Article Applies to:
All TP-Link LTE Gateway Routers including Archer MR600, TL-MR6400, etc.
Issue Description/Background:
Some customers reported that their Jio SIM card was working fine before, but the internet stops working after upgrading to 5G, old 4G Jio SIM card still works fine on the same device, while the 5G enabled Jio SIM card works on a smartphone or Jio's own router.
Available Solution
Before downloading and updating the following beta firmware, please verify the model number and hardware version on the product label, especially the models with x.0, x.20 and x.30 versions. Please note that the x.0, x.20 and x.30 are different versions and unable to use the same firmware.
For Archer MR600(EU) V3: Archer_MR600(EU)_V3_230811
For Archer MR600(EU) V2: Archer_MR600(EU)_V2_230801
For TL-MR6400(EU) V5.30: TL-MR6400(EU)_V5.30_230801
For TL-MR6400(EU) V5.20: TL-MR6400(EU)_V5.20_230815
For Archer MR200(EU) V5.30: Archer_MR200(EU)_V5.30_230816
For Archer MR200(EU) V5.20: Archer_MR200(EU)_V5.20_230815
For Archer MR400(EU) V4.30: Archer_MR400(EU)_V4.30_230928
For Archer MR600(EU) V1: Archer_MR600(EU)_V1_Builld_20231127
For Archer MR200(EU) V5: Archer_MR200(EU)_V5_24040425
For Archer MR200(EU) V6: Archer_MR200(EU)_V6_24040425
For TL-MR6400(EU) V5: TL-MR6400(EU)_V5_20240425
For TL-MR100(EU) V2: TL-MR100(EU)_V2_240313
Notes:
1) If there is still no internet or no IPv4 address when using the above beta firmware with Jio 5G SIM card, please check the default APN profile settings on Advanced->Network->Internet page, if the PDP Type is not on "XLAT", please create a new profile manually and set PDP Type as "XLAT", leave other parameters the same as default profile, then check if the problem will be resolved.
If so, please share with us the MCC&MNC of your SIM card, so that we could update the default profile settings for your SIM card.
You could insert the Jio 5G SIM card into your smartphone, then check the APN profile settings on the phone to find the MCC and MNC, please share with us the screenshot, thanks a lot!
2) The beta firmware is for Jio 5G SIM card only, please don't update it if you would like to use a different SIM card.
3) We will update this thread once there is any other beta firmware for other models or versions.
4) Please be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding
If internet still doesn't work with 5G Jio SIM after updating the above firmware, please make sure the PDP Type in the APN profile is XLAT, and provide the following information for further follow-up:
1. A screenshot of the Advanced > Status page.
2. A screenshot of the Advanced > Network > Internet page.
3. Save and send us the system log file. You can go to Advanced > System Tools > System Log page to save the log file.
4. Model number, hardware and firmware version of the TP-Link router.
Do let the community know if there is anything else that we can help with. We are always happy to help.
MODEL: MR600-V1
Firmware Version: 1.3.0 0.9.1 v0001.0 Build 210608 RC.66100n
Hardware Version: Archer MR600 v1 00000001
ISP version: 21082501
Troubleshooting Suggestions NOT WORKED. PROBLEM IS STILL THERE "4G: USER: Registration denied by the visible network!"
SYSTEM LOG AND SYSTEM SETTING'S SCREENSHOTS HAVE BEEN ATTACHED.
Some changes were suggested by the Tplink Indian team, this makes the SIM gets registered and even MR600 V1 ( with latest beta firware ) shows its connected to internet, but no internet access from the LAN port or wireless
@Sunshine Hi, Yes the MR-600 V1 says connected but even the Speed test built inside MR-600 says speed Zero and not connected to the internet. Only IPV6 matters and Authentication can be anything ( IPV4 does not connect at all ) . I have requested Jio to downgrade my SIM from 5G to 4G or else have to wait for thier AirFiber ( 5G CPE ) launch. LAN connected windows Devices and Wireless Connected laptops / Android Mobile does not get internet access from MR-600. IPV6 is selected in my laptop ( screenshot below ) . Will try to get the logs in IPV6 later ( IPV4 does not connect all - anyway will try to get both logs )
