Troubleshooting How to set up Port Forwarding on the Deco app
Port Forwarding is used to make a device or service in your home network accessible to computers on the internet. Typical applications include allowing remote management to security cameras within the local network, permitting access to HTTP, FTP and other local servers, etc..
Detailed instruction about How to setup:How to set up Port Forwarding feature on the Deco
If you have any issues about port forwarding or the opened ports are still closed, the following suggestions will provide you with some guidance.
1. Failed to configure port forwarding.
- The device is not on the “Select from Device” list.
Please check whether the server is used a static IP address. If yes, please change it to DHCP
Most of the time, Devices, such as NAS, NVR, Virtual Box, and PI-Hole are usually set up with static IP addresses, instead of DHCP, if you do not use to use DHCP, this link would provide a workaround.
Forward port to missing device
- Some error messages pop out during the configuration.
The troubleshooting depends on the error code and please comment below with a screenshot of your error message.
2. Port forwarding is set up correctly, but ports aren't open.
- First, please check whether you have a public IP address under Deco APP>More>Advanced>IPV4.
If this IP is a private address, you might have a double NAT issue and the port is blocked by the ISP gateway.
The available solutions are:
1. Set up Deco as an access point under Deco APP>More>Advanced>Operation mode;
2. Open the same port for Deco on the ISP gateway.
- Check the firewall settings on the server.
Windows firewall will block the connection from the different subnet, and it will divide the difference according to the network location you have chosen.
Please refer to this link to check whether you have a public IPV4 address and the LAN server is on the Public network profile:
https://www.tp-link.com/en/support/faq/785/
If the IPV4 IP is a public IP address, the configuration has no obvious mistakes, your case needs to be under further analysis, please comment below with the following details:
1.Please make sure UPNP disabled under Deco APP>More>Advanced.
2. Which ports did you wish to open? For which local devices?
3. Are you able to access this server via the same port on a local client?
4. How did you find out the port is still closed?
---If you have enabled TP-Link DDNS, except testing via the DDNS, please also test whether the server is accessible remotely via WAN IP address.
We do need more cases to complete the troubleshooting guides and please let me know which one is quite similar to your case, and if any of the suggestions works.
Thank you very much.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@TP-Link Deco Hello i wanted to forward my Minecraft Journey map mod online map i setup the port forward in the tp-link app on my pc it doest work i dont know how to fix this can you help me please that will be appreciated
- Copy Link
- Report Inappropriate Content
This was a nightmare, but finally resolved based on MANY variations and experiements.
(support just pasted in set up paragraphs as a reply)
latest everything, new deco units Jan 2025. Android app, latest android, etc. Seemingly no way to display app version (but it was JUST installed)
(an aside: it is so impractical to have to use an app instead of web-based management - one has to re type everything)
The problem was I could not DEFINE a port forward. It gave one of two errors:
- SAVE - failed (no information at all - a horrible error message... much like "something went wrong" messages where the software engrs were too lazy to specify...)
- IP address already in use (yes, it's the IP of the client i'm trying to forward to) (but if you CHOSE FROM THEIR LIST of IP addresses/clients, it would just "fail" )
In the end, i had to:
- turn off/disconnect(from the network) the client
- delete offline client IP (from a list/cache - listed after "clients online"
- delete an address reservation that was somehow made due to one of my port-forwarding save attempts
- only then would it accept the new rule, and it worked thereafter.
I don't understand why (and support would not answer) the app balked at an IP address that was the listener - it MUST exist in order to have something to FORWARD TO...
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 44857
Replies: 32
Voters 0
No one has voted for it yet.