Home Network Community > Deco > Deco in AP with PiHole
< Deco

Deco in AP with PiHole

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco in AP with PiHole

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco in AP with PiHole
Deco in AP with PiHole
2024-05-15 09:59:09 - last edited 2024-05-16 07:37:15
Tags: #Access Point Mode #Guest Network #Deco App Related #Network Connectivity
Model: Deco M4  
Hardware Version:
Firmware Version:

Hi! I have an Archer C80 as my main router and a few Deco's in Access Point mode. PiHole is connected to router, Main Deco is connected to router and from the Main Deco into a switch where everything else is connected. If I connect on of the PCs via WiFi to the Guest Network of the Deco, I get a DNS error. In Windows when connected to Guest Network, the DNS server shows the correct IP. Any ideas?

 

  0      
 
  0      
 
#1
Options
4 Reply
Re:Deco in AP with PiHole
2024-05-15 21:51:22

  @traian_n My understanding is that when in AP mode any clients connected to the Guest Wifi Network will only be able and communicate with the router and any other packets intened to local network resources will be dropped.

  1  
  1  
#2
Options
Re:Deco in AP with PiHole
2024-05-16 07:08:26

  @traian_n 

Hi, Did you use Pi-Hole as the LAN DNS server?

Under Access Point mode, the guest network is separated from the main network via Access control, instead of VLAN tags.

The guest client is only allowed to access the LAN gateway, which would be the LAN IP of Archer C80.

In this way, if Pi-Hole is the customized LAN DNS server, it is no longer reachable by Guest network devices.

 

Thank you very much and best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
  0  
  0  
#3
Options
Re:Deco in AP with PiHole
2024-05-16 07:38:49

  @David-TP So I should replace my router with one that supports the Pi Hole as my WAN DNS instead of LAN DNS and that whould do the trick, correct?

  0  
  0  
#4
Options
Re:Deco in AP with PiHole
2024-05-17 01:02:02

  @traian_n 

Hi, Sorry for the delay.

Yes, if the first main router supports using the LAN Pi-Hole as the WAN DNS server which would be a good solution for the current issue.

Thank you very much and best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 431

Replies: 4

Tags

Access Point Mode Guest Network Deco App Related Network Connectivity
Related Articles
Router or AP mode for Deco M4
2987 0
Deco M4 wired max 600mbps (AP mode)
744 0
 PiHole and XE75 question
801 2
Deco M4 as AP?
199 0
Deco XE75 - Guest network is not working - AP Mode - wired Backhaul
296 1
Router or AP?
479 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.