Home Network Community > 5G/4G Wi-Fi Routers/MiFi > Loosing 4g signal after powercuts
< 5G/4G Wi-Fi Routers/MiFi

Loosing 4g signal after powercuts

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Loosing 4g signal after powercuts

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Loosing 4g signal after powercuts
Loosing 4g signal after powercuts
2023-06-20 11:57:47
Model: Archer MR600  
Hardware Version: V2
Firmware Version:

Hi. I have set up a TP Link MR600 to an LTE aerial to get internet for both my dad and a friend of mine. Both work very well until there is a power cut. Then the 4g signal will not reestablished for long periods of time. Sometimes taking out and refitting the SIM card allows it to gain 4g signal again. Has anyone any ideas? When this works it works well but when it stops it can be a pain to get it back. Both routers were bought at the same time. 

Thanks

Gerry

  0      
 
  0      
 
#1
Options
3 Reply
Re:Loosing 4g signal after powercuts
2023-06-21 10:12:34

  @GerryF1 

 

Hi, the issue only happens when there is a power outage in the area or also happens if you just unplug the power adapter and plug it back?

 

In addition, who is the ISP and what is the firmware version of the two MR600 V2?

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Loosing 4g signal after powercuts
2023-06-21 13:59:16

  @Sunshine  it also happens if you plug out the power supply. The version is version 2

  0  
  0  
#3
Options
Re:Loosing 4g signal after powercuts
2023-06-26 09:08:17

  @GerryF1 

 

Hi, could you please try unplugging the power supply and then plugging it back, wait for at least 5 minutes, if no 4G signal, please share with us screenshots of Advanced->Status page, Advanced->Network->Internet page along with the system log file saved on Advanced->System Tools->System Log page.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 537

Replies: 3

Related Articles
Router keeps on loosing signal
680 0
No indication of 4g+ signal
867 0
 4g signal dropped
1074 0
Archer MR600 4G+ Router Not Getting Network Signal
1594 0
 All my 4G routers stopped to find 4G signal
507 0
 MR600 4G+ Signal Problem?
2518 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.