No indication of 4g+ signal

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

No indication of 4g+ signal

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
No indication of 4g+ signal
No indication of 4g+ signal
2020-08-02 10:37:17 - last edited 2020-08-05 00:48:15
Model: Archer MR600  
Hardware Version: V1
Firmware Version: 1.2.0 0.9.1 v0001.0 Build 200511 Rel.44954n

Hi there,

 

I'm getting  4g+ signal in my phone but not in my MR600 with the same sim card. I tried playing with APN settings but that didnot help and tried resetting the device and that did not help either. I did upgrade my ISP as well but no help. Do any anyone have any idea about what could be the problem? Should I replace the device?

 

Thanks in advance,

Sreeni

  0      
  0      
#1
Options
1 Accepted Solution
Re:No indication of 4g+ signal-Solution
2020-08-04 05:36:42 - last edited 2020-08-05 00:48:15

@Sunshine 

 

Thanks for the reply. I got this resolved by contacting your live support. They did provide me a beta firmware to update and that bring up 4G+ network. However like others mentioned in the forum already I have to do the Band A and Band B selections manually to get 4G+ working everytime I restart the router. 

 

Will there be a permanent fix for auto selection of Bands? A final firmware which would address all this issue permanently?

 

-Thanks

Recommended Solution
  0  
  0  
#3
Options
2 Reply
Re:No indication of 4g+ signal
2020-08-03 09:23:24

@ArcherMR600 

Hi,

For your case, we hope you could help us get the following information:

  1. What is the model of the sim card and who is your sim card provider?
  2. Please check on the status page, is there any IP address or is it 0.0.0.0?

--if it is not 0.0.0.0, please try to change the DNS to 8.8.8.8/8.8.4.4 under advanced-->network--->LAN settings, then reboot the router;

--if it Is 0.0.0.0, please reset the router and keep the default APN settings, then save the system log after 5-10mins;

Later, our related support would get in touch for further assistance.

Thank you.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:No indication of 4g+ signal-Solution
2020-08-04 05:36:42 - last edited 2020-08-05 00:48:15

@Sunshine 

 

Thanks for the reply. I got this resolved by contacting your live support. They did provide me a beta firmware to update and that bring up 4G+ network. However like others mentioned in the forum already I have to do the Band A and Band B selections manually to get 4G+ working everytime I restart the router. 

 

Will there be a permanent fix for auto selection of Bands? A final firmware which would address all this issue permanently?

 

-Thanks

Recommended Solution
  0  
  0  
#3
Options