RE450 V2 LED and power control doesn't work after firmware update to 1.0.5
RE450 V2 LED and power control doesn't work after firmware update to 1.0.5
After updating RE450 V2 to 1.0.5 firmware neither the LED control and Power Schedule doesn't work. I reflashed the firmware, but with no luck!
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi,
If anyone had the same issue later, please refer to the following details:
It is caused by the DST(Daylight Saving Time) on the RE450.
Please disable the DST(Daylight Saving Time) to make the LED control function work first.
We will solve this problem later with the new firmware.
Thank you very much for your understanding and support.
- Copy Link
- Report Inappropriate Content
Hello everyone,
Thank you for your feedback and patience our engineer investigate and provide a fix.This has been fixed on the RE450 V2 newer firmware.
Model: RE450 V2
Description : LED and power control doesn't work properly since the Daylight saving time starts in 2020.
Fix/ Solution: this has fixed on RE450 V2 1.0.6 RE450(EU)_V2_210301 and later firmware released in April,2021
Try to factory reset range extender after the firmware update and reconfigure it, the problem should be resolved.
RESET: with RE powered on , use a pin to push reset hole until all the LEDs flash once.
As this an old topic and issue has been solved in 2021, this thread will be temporarily closed.
For additional feedback, please view Range extender Official & Hightlighted Threads and see if it helps with your case, or start a New Thread for your range extender.
More Articles:
[Configuration Guide] TP-Link Range Extender Setup (Range Extender Mode)
[Troubleshooting] Has connected to TP-Link extender but no internet, what can I do?
[Troubleshooting] What should I do if Internet speed becomes slow via Range Extender?
[Troubleshooting] Unable to Connect to WiFi Extender or Saying Incorrect Password
- Copy Link
- Report Inappropriate Content
Good day,
Thanks a lot for your time and patience.
Except for the LED control, power schedule, did the internet service work fine?
When you said it was not working, did it take effect at the wrong time, or did not turn on/off at all?
Have you checked if the device time on RE450 was still correct?
And have you tried to reset the RE450, then set up the LED control or power schedule again?
Thank you very much.
- Copy Link
- Report Inappropriate Content
TP-Link wrote
Good day,
Thanks a lot for your time and patience.
Except for the LED control, power schedule, did the internet service work fine?
Internet works with intermittent outages like the others described on few other topics.
When you said it was not working, did it take effect at the wrong time, or did not turn on/off at all?
Have you checked if the device time on RE450 was still correct?
And have you tried to reset the RE450, then set up the LED control or power schedule again?
Thank you very much.
Hello!
There are intermittent outages like described in the few other topics. From time to time can't browse the internet from the equipment connected to RE450. At the same time hosts connected to the main router have an internet connection.
LED and power control not working at all. The time on RE450 is correct. I restored to factory defaults and set the device from scratch.
The problem is definitely with firmware version because I have installed 1.0.4 and LED control worked.
KR
- Copy Link
- Report Inappropriate Content
Good day,
Thank you very much for your kind reply.
We would like to follow up your case by email and please have a check of your email box later.
Thanks
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi,
If anyone had the same issue later, please refer to the following details:
It is caused by the DST(Daylight Saving Time) on the RE450.
Please disable the DST(Daylight Saving Time) to make the LED control function work first.
We will solve this problem later with the new firmware.
Thank you very much for your understanding and support.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@TP-Link I can confirm disabling DST works. I can manually change time if no firmware update happens before DST this year!
- Copy Link
- Report Inappropriate Content
When this firmware is planned to be released?
- Copy Link
- Report Inappropriate Content
@Friga its not worke
- Copy Link
- Report Inappropriate Content
Hello everyone,
Thank you for your feedback and patience our engineer investigate and provide a fix.This has been fixed on the RE450 V2 newer firmware.
Model: RE450 V2
Description : LED and power control doesn't work properly since the Daylight saving time starts in 2020.
Fix/ Solution: this has fixed on RE450 V2 1.0.6 RE450(EU)_V2_210301 and later firmware released in April,2021
Try to factory reset range extender after the firmware update and reconfigure it, the problem should be resolved.
RESET: with RE powered on , use a pin to push reset hole until all the LEDs flash once.
As this an old topic and issue has been solved in 2021, this thread will be temporarily closed.
For additional feedback, please view Range extender Official & Hightlighted Threads and see if it helps with your case, or start a New Thread for your range extender.
More Articles:
[Configuration Guide] TP-Link Range Extender Setup (Range Extender Mode)
[Troubleshooting] Has connected to TP-Link extender but no internet, what can I do?
[Troubleshooting] What should I do if Internet speed becomes slow via Range Extender?
[Troubleshooting] Unable to Connect to WiFi Extender or Saying Incorrect Password
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 4026
Replies: 10