Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > OneMesh between AX10 and C7 V5

< All Threads

OneMesh between AX10 and C7 V5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

OneMesh between AX10 and C7 V5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Teodorl91

2024-01-02 21:08:00 - last edited 2024-01-31 07:47:04

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2024-01-02

OneMesh between AX10 and C7 V5

2024-01-02 21:08:00 - last edited 2024-01-31 07:47:04

Tags: #EasyMesh #OneMesh

Model: Archer AX10 Archer C7

Hardware Version: V5

Firmware Version:

Hello everyone and apologize if this was discussed many times but I have difficulties finding the right solution.

My ISP provide an Archer AX10 router that is connected to the modem through LAN1 and it works briliant.

Also I have my old AX1750 C7 V5 which I want to use it as an wireless access point.

Both routers have the EasyMesh option in the WebUI but I cannot manage to mesh them together. I have updated to the latest firmware available, but still no luck.

Am I doing something wrong? Is this possible between these routers?

Thank you!

1 Accepted Solution

terziyski

LV7

2024-01-03 02:18:59 - last edited 2024-01-31 07:47:04

Posts: 7142

Helpful: 5359

Solutions: 1220

Stories: 7

Registered: 2013-10-12

Re:OneMesh between AX10 and C7 V5-Solution

2024-01-03 02:18:59 - last edited 2024-01-31 07:47:04

@Teodorl91

Archer C7 v5 supports only Onemesh. To be able to connect two routers in mesh they both have to support Easymesh.

There have been a successful attempts ( using the WPS method ) to build a mesh between an Easymesh and Onemesh router, but the main router should be the one that supports Onemesh.

You can try that if it suits your needs. Otherwise using Archer C7 v5 in AP mode (Case 1) will work in your case, but without a mesh.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Recommended Solution

1 Reply

terziyski

LV7

2024-01-03 02:18:59 - last edited 2024-01-31 07:47:04

Posts: 7142

Helpful: 5359

Solutions: 1220

Stories: 7

Registered: 2013-10-12

Re:OneMesh between AX10 and C7 V5-Solution

2024-01-03 02:18:59 - last edited 2024-01-31 07:47:04

@Teodorl91

Archer C7 v5 supports only Onemesh. To be able to connect two routers in mesh they both have to support Easymesh.

There have been a successful attempts ( using the WPS method ) to build a mesh between an Easymesh and Onemesh router, but the main router should be the one that supports Onemesh.

You can try that if it suits your needs. Otherwise using Archer C7 v5 in AP mode (Case 1) will work in your case, but without a mesh.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Information

Helpful: 0

Replies: 1

OneMesh between AX10 and C7 V5

OneMesh between AX10 and C7 V5

Information

Voters 0

Tags