Home Network Community > All Threads > Static Route to my Fritzbox Router
< All Threads

Static Route to my Fritzbox Router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Static Route to my Fritzbox Router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Static Route to my Fritzbox Router
Static Route to my Fritzbox Router
2023-06-26 10:06:44
Tags: #routing
Model: Archer AX3000  
Hardware Version: V1
Firmware Version: 1.2.3

Hello,

 

my TP-Link Router is connected through the Gateway Port to my Fritzbox. I tried to ping and access my Fritzbox but without any success. 

 

My TP Link Network is 192.168.178.1.50 - 192.168.2.254. Default Gateway is 192.168.1.1 and Subnet is 255.255.0.0.

 

My Fritzbox network is 192.168.178.50 - 192.168.178.200 and the Fritzbox itself has the IP 192.168.178.1.

 

On my TP-Link Router in Network => Routing I added a static route to network destination 192.168.178.1, Subnet 255.255.255.255 Interface LAN/WAN and Default Gateway 192.168.1.1.

 

I cannot ping nor access my fritzbox. Any ideas what I did wrong?

 

Best regards

Mafu

  0      
 
  0      
 
#1
Options
2 Reply
Re:Static Route to my Fritzbox Router
2023-06-26 15:52:30 - last edited 2023-06-26 16:16:02

  @mafu89 

 

Assuming the connection is Fritzbox LAN port => AX3000 WAN port:

Your Fritzbox DHCP network is 192.168.178.50 - 192.168.178.200 and the Fritzbox itself has the IP 192.168.178.1.

If your AX3000 WAN port is set to "Dynamic IP" it should obtain an IP address from this range (192.168.178.50 - 192.168.178.200).

When setting AX3000 LAN IP address (for example 192.168.1.1/24 i.e. with netmask 255.255.255.0) you should be able to access Fritzbox IP (192.168.178.1) without setting any static route on AX3000.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  1  
  1  
#2
Options
Re:Static Route to my Fritzbox Router
2023-06-26 19:31:36

  @mafu89 

 

As pointed out by @terziyski , you should not have any problems accessing the Fritzbox if your network is set up correctly.


I am slightly confused as to why your AX3000 network is so large (subnet mask 255.255.0.0) and also has overlapping IPs with the Fritzbox in the 192.168.178.x range. If things are still not working for you, I have several questions:


1. How are the two routers interconnected?  WAN-to LAN?  LAN-to-LAN?


2. Are you using a PC for accessing the AX3000 and the Fritzbox?  If so, what IP address (and subnet mask) is assigned to the PC?  Where is the PC connected?


3. Is the DHCP server enabled in both routers?  If so, what is the range of the AX3000 DHCP server?


 

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 1024

Replies: 2

Tags

routing
Related Articles
Setup Static Route for Deco M5
22802 16
Static route disables itself
738 0
static route not working
4171 1
Static route support
1112 1
Adding Static Route
503 0
No internet after making static route using M5
404 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.