Home Network Community > All Threads > static route not working
< All Threads

static route not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

static route not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
static route not working
static route not working
2020-10-19 19:24:38
Model: Archer C2300  
Hardware Version: V1
Firmware Version: 2.0.3

the archer is the router between the internet and the local network of 192.168.6.0/24

there is a router at 192.168.6.3 that connects to 192.168.131.0/24

 

I want my laptop (192.168.131.2) to ping my computer (192.168.6.113) 

 

I added a static route in the archer Advanced -> network -> static routing

 

network destination: 192.168.131.0
subnet mask: 255.255.255.0
default gateway: 192.168.6.3
interface: lan


 I put the check in enable this entry and then I can ping the archer (192.168.6.1) from my laptop, but not my computer. I put a static route on another host (192.168.6.2) and I can ping that one from my laptop too, but in the end, I want to control a light which I can not put a static route onto.

 

How do I set up a static route on the router so that I can get my laptop to ping my computer?

 

 

 

 

  1      
 
  1      
 
#1
Options
4 Reply
Re:static route not working
2021-04-02 09:34:21
I have the same issue. Have you managed to solve it?
  0  
  0  
#2
Options
Re:static route not working
2021-04-07 07:39:32

@herrwamm 

 

Can you provide the detailed network layout, how are the devices connected, and what are the IP address and gateway on them? Then we will try to figure it out.

 

Meanwhile, you can refer to this guide to configure the static route on the router:

https://www.tp-link.com/support/faq/560/

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#3
Options
Re:static route not working
2021-04-20 18:19:37

@jackn007 

 

Hi, what am I doing wrong? I have a router (Mikrotik) at home, where I have the main range 192.168.0.X(/24) and two other routers (without NAT, in their range ending 192.168.(1-2).1) with secondary ranges 192.168.1.X/24 and 192.168.2.X/24. Devices from these ranges normally access the Internet and can communicate across ranges on the network.

 

When I replaced Mikrotik with TP-Link Archer AX73, set the same IP address, so I found out that only the routers themselves can access the Internet, but their clients do not. The configuration on the secondary routers did not change, I just replaced the main router (Mikrotik) with TP-Link with the same configuration.

 

When I tracert to these ranges (from main range 192.168.0.X to 1.X or 2.X), it goes to the main router (192.168.0.1) and then out to the Internet (not within the LAN).

Can this TP-Link be used as a classic router, which allows to have more ranges (using other routers in the LAN)?

 

Thank you.

  0  
  0  
#4
Options
Re:static route not working
2021-04-21 05:18:48 - last edited 2021-04-21 05:28:18

A similar issue has been discussed in this thread. It may prove helpful.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#5
Options

Information

Helpful: 1

Views: 4178

Replies: 4

Related Articles
Setup Static Route for Deco M5
22802 16
Static route disables itself
738 0
Static route support
1112 1
Adding Static Route
503 0
No internet after making static route using M5
404 1
The static route is not reflected after setting.
613 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.