Home Network Community > All Threads > Ddns to link service only and ip mismatch
< All Threads

Ddns to link service only and ip mismatch

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Ddns to link service only and ip mismatch

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Ddns to link service only and ip mismatch
Ddns to link service only and ip mismatch
2023-03-07 09:51:25 - last edited 2023-03-07 11:47:42
Tags: #DDNS
Model: Deco X60  
Hardware Version:
Firmware Version: 1.0.15 Build 20221111 Rel. 77798

Firstly, the Deco DDNS Setup instructions mention you can choose the DDNS service. Through the deco app currently I only have the switch for TP-Link DDNS. 
 

Secondly, even if I reboot the main router, 

nslookup of the TP Link DDNS address differs from the internet ip shown on the connection settings. 

 

Funny enough, on reboot I noticed the ddns ip did change from one 102 address to another but the actual ip address on the router itself is a 100 address.

 

Basically I'm tying to port forward ssh externally.

  0      
 
  0      
 
#1
Options
2 Reply
Re:Ddns to link service only and ip mismatch
2023-03-08 02:44:10

  @Elfstones 

Hi, May I know who is your internet service provider?

I see some service providers might use CG-NAT on their networks:

CG-NAT Blocks my OpenVPN and restricks the NAT type

Best regards.

 

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:Ddns to link service only and ip mismatch
2023-04-26 01:11:45 - last edited 2023-04-26 01:12:04

  @David-TP 

Hi, Thanks for the message.

I see the Linksys WRT-1900ACS supports OpenWRT and I think additional configurations might have been done on the Linksys.

And I noticed you mentioned the internet connection type on Deco is PPPOE, most of time, PPPOE could get a public IP address but it seemed like you still get a private one-the 100 ips on IPv4 on Deco. I hope you could check with South Africa's Webafrica to see whether they could provide a public IP address or open the related ports on ISP gateway for Deco X60.

 

By the way, May I know what you set up TP-Link DDNS for, remotely accessing a local server?

Thank you very much.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#3
Options

Information

Helpful: 0

Views: 411

Replies: 2

Tags

DDNS
Related Articles
DDNS points to another ip address
380 0
DDNS reporting wrong IP
0 0
Cannot setup DDNS
356 0
DDNS Service Provider
912 1
DDNS resolved difference IP from the PPPoe IP
908 0
TL-WR1043ND and NO-IP as DDNS services
873 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.