Home Network Community > All Threads > Archer AX50 as AP
< All Threads

Archer AX50 as AP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer AX50 as AP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer AX50 as AP
Archer AX50 as AP
2021-08-12 20:35:02
Model: Archer AX50  
Hardware Version: V1
Firmware Version: 1.0.9 Build 20200708 rel.55037

Hello,

 

i purchased Archer AX50 2 days ago, setup manual.

1- ISP router ONT ---- Archer AX50 (cat6)

2- ISP router gateway 192.168.100.1

3- Archer AX50 static IP 192.168.100.90

4- Archer AX50:

 - connected to LAN1

 - Disable DHCP

 - New SSID

 - Smart Wifi

 

everything goes great till today, wifi works fine but no internet(for a while and i should reboot device to wake it up! no Cable issue i was using TL-WR940N without any issue for long time!

 

any advices? or steps i forgot! 

  0      
 
  0      
 
#1
Options
4 Reply
Re:Archer AX50 as AP
2021-08-12 21:49:23 - last edited 2021-08-12 21:52:49

@iSalalah 

 

Here's how to configure AX50 in AP mode - Case 1.

Use the AX50 WAN port (not LAN1) to connect to the ISP router.

Set AX50 IP address outside or at the end of ISP router DHCP IP address range.

Other settings are fine, you can experiment with SmartConnect on/off to see if that suit your needs.

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Archer AX50 as AP
2021-08-12 22:09:43

@terziyski 

 

Thanks for you quick response.

 

Is below step necessary? 
 

terziyski wrote

Set AX50 IP address outside or at the end of ISP router DHCP IP address range.

Should put AX50 IP out main router range?!

 

As I'm going to disable DHCP server in AX50!

 

please advise, thanks 😊 

 

  0  
  0  
#3
Options
Re:Archer AX50 as AP
2021-08-12 22:21:07 - last edited 2021-08-12 22:47:49

@iSalalah 

 

Connect ISP router LAN port to AX50 WAN(Internet) port.

Change AX50 Operation Mode to Access Point.

If the ISP router DHCP server range is (192.168.100.2-192.168.100.99), set AX50 LAN IP address 192.168.100.100.

If you don't know what the ISP router DHCP server range is, just set AX50 LAN IP address 192.168.100.254.

Turn AX50 DHCP server off.

 

 

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#4
Options
Re:Archer AX50 as AP
2021-08-13 06:35:20

@terziyski thanks for your help,

 

i just do this steps in AX50

- change mode to AP

- static IP within main router range

- connect LAN >> LAN

- disable DHCP server 

 

it works great for now, hope this will fix issue permanently :-)

  1  
  1  
#5
Options

Information

Helpful: 0

Views: 1305

Replies: 4

Related Articles
Archer AX50
1127 2
Archer AX50 with Plusnet
893 0
Archer AX50 - Jerky transfers in AP mode
724 0
Archer AX50 guest isolation in AP mode
995 0
Archer AX50 with RJ11, possible?
579 0
Archer ax50 dfs fix
885 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.