AC1200 Deco E4 - Setup Okay - but no internet connection (although Wifi looks right)
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
** Please note - my unit not in Model dropdown ** It is a tp-link AC1200 Deco E4
I setup my unit - Setup process went smoothly.
Once completed, i could see the wifi just created and it said 'Connected, Secured' on my laptop
However I was unable to access the internet on laptop or phone that the setup was run from.
Reset device and repeated the setup - same result.
Changed the Ethernet cable and reset device, repeated setup - no change.
Help!!
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I was having the same problem with RSAWeb. For anyone else experiencing this, the issue turned out to be that I had to re-activate my fiber via their website before the internet worked.
- Copy Link
- Report Inappropriate Content
Hi， After the setup, did Deco E4 turn white or red?
If you go to Deco APP>More>advanced>IPV4, is there any IPv4 address here?
By the way, who is your internet service provider?
Thank you very much.
- Copy Link
- Report Inappropriate Content
@TP-Link Hi There,
It installed successfully (white logo - not Red).
I do seem to remember an IPv4 address, but didn't record it unfortunately.
I am in South Africa, Cape Town - I have fibre connection (100MBPS) with RSAWeb (used for over 1 year now).
I have reverted back to my standard router - i will try again this weekend.
(Please if you can think of anything else to try that would be greatly appreciated.
Thanks Steve.
- Copy Link
- Report Inappropriate Content
Hi,
If there is an IPV4 address, I think we could try to change the DNS to have a look:
- Copy Link
- Report Inappropriate Content
@TP-Link I tried again quickly -
Here are my settings (viewed with Win10 Network properties):
Working Fibre Settings:
SSID: TP-FAR01
Protocol: Wi-Fi 4 (802.11n)
Security type: WPA2-Personal
Network band: 2.4 GHz
Network channel: 6
Link speed (Receive/Transmit): 144/144 (Mbps)
Link-local IPv6 address: fe80::9164:22d8:1193:588a%25
IPv4 address: 192.168.0.109
Manufacturer: Intel Corporation
Description: Intel(R) Dual Band Wireless-AC 8260
Driver version: 20.70.16.4
Physical address (MAC): E4-A7-A0-1F-7C-BE
New DECO Network:
SSID: FAR2-DECO
Protocol: Wi-Fi 5 (802.11ac)
Security type: WPA2-Personal
Network band: 5 GHz
Network channel: 36
Link speed (Receive/Transmit): 866/866 (Mbps)
Link-local IPv6 address: fe80::9164:22d8:1193:588a%25
IPv4 address: 192.168.68.101
IPv4 DNS servers: 41.79.37.3
41.215.234.106
192.168.68.1
Manufacturer: Intel Corporation
Description: Intel(R) Dual Band Wireless-AC 8260
Driver version: 20.70.16.4
Physical address (MAC): E4-A7-A0-1F-7C-BE
Viewed on App:
<-IPv4
WAN
Internet Connection Type
Dynamic IP
IP Address
41.71.36.161
Subnet Mask
255.255.255.192
Default Gateway
41.71.36.129
Primary DNS
41.79.37.3
Secondary DNS
41.215.234.106
- Copy Link
- Report Inappropriate Content
Hi, the IP settings are quite normal and Were you able to get internet service?
Would changing the DNS on the Deco make any difference?
please also try to reboot the ISP modem(or power off the modem for a while then power back) in case there is any IP-MAC binding;
Thank you very much.
- Copy Link
- Report Inappropriate Content
I was having the same problem with RSAWeb. For anyone else experiencing this, the issue turned out to be that I had to re-activate my fiber via their website before the internet worked.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1872
Replies: 6
Voters 0
No one has voted for it yet.