Home Network Community > All Threads > AX10/AX1500 bricked router not accepting firmware
< All Threads

AX10/AX1500 bricked router not accepting firmware

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AX10/AX1500 bricked router not accepting firmware

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
AX10/AX1500 bricked router not accepting firmware
AX10/AX1500 bricked router not accepting firmware
2020-11-29 16:59:03
Model: Archer AX10  
Hardware Version: V1
Firmware Version:

 

I have the Archer AX10(EU) hardware version 1.0 (also titled Model AX10 AX1500 WiFi 6 Router).
I visited today the router control panel first time after a few months. The page notified that there is a new firmware available. I clicked update.

The device started update, control page stopped responding, all leds went off except for one constant orange ( I guess it's the internet access led).

After several minutes I tried to reboot it with no success. The lighs blink at boot but only constant orange stays.


Finally was able to access the control page at http://192.168.0.1/ and it showed rescue mode.

 

I'm not able to upgrade any firmware. The page always says: "Upgrade failed. The file is invalid."

 

I tried the both 2 EU version firmwares from https://www.tp-link.com/fi/support/download/archer-ax10/#Firmware
Just in case, I then tried also the US version firmwares and files for AX1500, and finally the firmwares offered on this topic https://community.tp-link.com/en/home/forum/topic/204398?utm_source=Subscription&utm_medium=email

Nothing works.

 

  0      
 
  0      
 
#1
Options
4 Reply
Re:AX10/AX1500 bricked router not accepting firmware
2020-11-29 20:09:28 - last edited 2020-12-05 13:23:57

@jjj6 

 

Here (https://static.tp-link.com/2020/202009/20200925/Archer%20AX10(EU)_V1_200827.zip)

is the latest FW for your device. You can't put US version if your router is an EU version.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#2
Options
Re:AX10/AX1500 bricked router not accepting firmware
2020-11-30 05:27:51

@jjj6 

 

Hello, try the firmware recovery in this article to confirm if you can bring it alive:

https://community.tp-link.com/en/home/stories/detail/582

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#3
Options
Re:AX10/AX1500 bricked router not accepting firmware
2020-12-04 18:32:25

Thanks for tips. Unfortunaly that didn't work.

Firstly, I can not use the link https://static.tp-link.com/2020/202009/20200925/Archer%2520AX10(EU)_V1_200827.zip
directly since I get the warning "Please go to TP-Link Offical Website to get products, software and services for your region."

Anyway, the filename in the link was quite interesting since I'm not able to see that listed in the pages for Finland https://www.tp-link.com/fi/support/download/archer-ax10/#Firmware
After replacing "fi" with "uk" I did find the file. The router even accepted but after upgrade goes to the same Rescue state.

Also, the router doesn't accept any other (older) firmwares from the UK site.

 

Regarding the rescue alternatives, I'm not quite sure but since this router has the HTTP Rescue page I assume it doesn't support TFTP (and would it even provide any "harder" reset than the web page?). I briefly tried it out but it seemed like the router didn't try to access TFPT using 192.168.0.86 for the server.

 

  0  
  0  
#4
Options
Re:AX10/AX1500 bricked router not accepting firmware
2020-12-20 14:24:24

Finally had some more time to dig in to the issue so I went as far as opened up the cover and connected a serial cable (somewhat according to this https://www.youtube.com/watch?v=IHNrnLnLakE ).
One of the last messages in the boot log was about reset button being set.
Not quite sure if this had been the issue all the time since I had tried reset multiple times.
But maybe it was somehow mechanically stuck against the case.
When I made sure the button is not pressed anymore then the router started up properly and even my old settings were there.

  8  
  8  
#6
Options

Information

Helpful: 0

Views: 3670

Replies: 4

Related Articles
AX10/AX1500 router not accepting firmware
728 0
AX10/AX1500 LACP
1081 0
OneMesh Not enabled On AX10 (AX1500)
1850 0
AX1500 Archer AX10
1038 0
AX10 (AX1500) Router will not connect to NBN Internet
631 0
Ax10 (ax 1500) 1.2.4 firmware
1269 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.