Home Network Community > All Threads > AX50 connected with TL-SG108E by GAP
< All Threads

AX50 connected with TL-SG108E by GAP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AX50 connected with TL-SG108E by GAP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
AX50 connected with TL-SG108E by GAP
AX50 connected with TL-SG108E by GAP
2020-03-15 02:01:09
Model: AC50  
Hardware Version: V1
Firmware Version: 1.0.6 Build 20200121 rel.54912

Model: Archer AX50 & TL-SG108E(UN) Ver. 4.0

 

Hello!

 

I would like to use link aggregation to enhance my network speed. The connection is as the following.

 

Internet <==> AX50 Port 3 & 4 (LAG) <==> TL-SG108E Port 1 & 2 (LAG) <==> NAS, PC, Printer...

 

After the setting and waiting around 3-5 minutes, the machines (NAS, PC, Printer) could get the IP address and link to internet. However, the network connection is not stable. The machines can't link internet after around 20-30 minutes and re-link to internet again. And, sometimes the speed is slower than without LAG (Only Giga Ehternet connection between AX50 and TL-SG108E).

 

My questions are:

1. Is my network connection correct? Can AX50 and TL-SG108E work normally when connect together by LAG? 

2. If the connection is correct, is there any step-by-step setting guide for setup LAG for this network connection?

 

Thanks a lot!

 

Ian

  0      
 
  0      
 
#1
Options
1 Reply
Re:AX50 connected with TL-SG108E by GAP
2020-03-16 11:21:23

@Dizzypapa 

 

Hello Ian, thanks for your information. The current network diagram should be fine, and below is the instruction to setup Link Aggregation.

https://www.tp-link.com/support/faq/1583/

 

We will do further analysis to locate this issue and try to figure it out. 

 

1. What is the led status of the Archer AX50 when you lost internet connection? Please connect your computer to the AX50 directly, bypass the switch and verify whether you can access internet or not.

 

2. At that time, please connect your computer to the AX50/switch and click here to get its IP address and gateway; try to ping the gateway of the main router and show us the ping results. And please ensure that there is no IP conflict between the AX50 and the TP-Link switch. 

 

3. What is the bandwidth you paid? And what is the actual speed you can get from the router with LAG enabled/disabled? 

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 820

Replies: 1

Related Articles
Gap in your product lineup... revisit AX50 and OneMesh
1071 0
Firmware Gap
1143 0
USB Printer Controller for Archer AX50
3273 0
TL-SG108E not managable
5372 0
AX50 WAN not working
539 0
Deco x20 and TL-SG108E
1028 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.