Early Access Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection
This Article Applies to:
Archer BE800 V1
New Features and Modifications:
This firmware introduces wireless driver enhancements for improved system stability and compatibility, along with a lot of new features, such as DoH/DoT and EasyMesh in AP mode. It's strongly recommended to upgrade to this version.
Important: Once upgraded to the 1.2.x firmware, you CANNOT downgrade back to the 1.1.x version.
New Features:
1. Upgraded wireless drivers for enhanced system stability and compatibility.
2. Newly support 3-band (2.4GHz + 5GHz + 6GHz) MLO connection.
3. Newly support EasyMesh in AP mode.
4. Newly support EasyMesh Topology Map.
5. Newly support WebUI in EasyMesh Satellite/Agent mode, providing functions like LED control, reboot, firmware upgrade, and more.
6. Newly support DoH/DoT.
7. Newly support ECO mode.
8. Newly support setting Wi-Fi Schedule separately for different Wi-Fi channels.
9. Newly support Guest network isolation from the main network in AP mode.
10. Newly support multi-selection in the Access Control allow list.
11. Newly support TAP mode in OpenVPN server function.
12. Newly support setting the client IP range of the PPTP/L2TP/IPSec VPN servers to match the main network's DHCP range.
13. Optimized traffic recognition with newly supported DPI function.
14. Enhanced system stability and security.
Firmware Download
Before the Upgrade
(1) Please be sure you have read the Beta Test Agreement before upgrading the pre-release firmware!
(2) For the sake of insurance, it's always recommended to save a copy of the router Backup Config file before upgrading or downgrading.
(3) You may follow the guide to upgrade the firmware of your router. How to Upgrade the Firmware on the TP-Link Wi-Fi Routers.
(4) This pre-release firmware for Archer BE800 V1 can be applied to all versions (EU/US/CA/AU/SG/etc.).
(5) To use the new 3-band MLO connection, both the router and client device must support Wi-Fi 7 and 3-band MLO. Please note that most Wi-Fi 7 smartphones and network adapters may only support 2.4GHz + 5GHz or 2.4GHz + 6GHz when connecting to the MLO Network.
Direct Firmware Download link:
Archer BE800_V1_1.2.1 Build 20250108 (Pre-release Software)
Additional Information
As always, we value your feedback. If somehow you encounter an issue during or after the router firmware upgrade, it's suggested to comment below with the following info. Your input helps us continue to improve and provide the best possible products and support.
- Detailed issue description, and provide more information on the specific conditions that seem to trigger the problem.
Related Articles:
EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller
Wi-Fi Routers Support DoH and DoT Network
What is WiFi 7’s Multi-Link Operation (MLO)?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Theo-Lyon wrote
Do you open ssh in this version ?
I want to apply my rules for iptables (block ip for country) because it is not possible with the GUI interface.
Thank
@Theo-Lyon Nope. The device doesn't allow it to be managed through SSH.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Theo-Lyon wrote
@Theo-Lyon Can you explain it in detail? Since you cannot manage the iptables via SSH, I'm afraid it may not be achievable.
- Copy Link
- Report Inappropriate Content
@Kevin_Z i live in Norway and my internet / ipv6 provider is Altibox. i belive they use native dual-stack ipv6. DHCPv6-PD.
no it has always been a problem everytime my router reboot i have to manually push renew a couple time.. Sometimes have to release and renew..
- Copy Link
- Report Inappropriate Content
I have a list of countries that I need to block and VPN server.
For example, any attempt to connect to our network from certain countries must fail, or connection attempts from NordVPN, CyberGhost, etc.
Rules with my actually router :
DROP all -- anywhere anywhere -m geoip --destination-country ......
(INPUT & FORWARD)
- Copy Link
- Report Inappropriate Content
Does the IPv4 always reconnect properly after the BE800 restarts?
To assist and figure it out efficiently, I'll forward your case to the TP-Link support engineers who will contact you with your registered email address later. Please pay attention to your email box for follow-up. Thank you.
- Copy Link
- Report Inappropriate Content
@Kevin_Z yes ipv4 always reconnect properly after BE800 restart, only ipv6 that wont reconnect and have to manuely reconnect push renew 2-4 times.. somtimes i have to relase then renew.. anoying
- Copy Link
- Report Inappropriate Content
Information
Helpful: 3
Views: 6948
Replies: 97
Voters 2
