Is possible connect Linksys PAP2T adapter to Archer BE550?
Is possible connect Linksys PAP2T adapter to Archer BE550?
Hi Team !!!
Is possible connect Linksys PAP2T adapter to Archer BE550 ?
TIA!
Regards,
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Thank you so much for all the details.
Is it possible to modify the 10/100 M RJ-45 network interface settings on the Linksys PAP2T adapter? If possible, please try to fix it on 100Mbps and then check if it can get a valid connection from the BE550 directly.
If possible, could you please try to modify the link speed on a wired computer to 100Mbps, connect it to one of the 2.5G LAN posts of the BE550, then check if the wired computer can connect to the internet properly. You can refer the steps provided in this article to modify the adapters settings on the Windows computer:
https://community.tp-link.com/en/home/forum/topic/723366
Updated on Feb 14, 2025:
Our development team also provides beta software to address this issue. Please upgrade and install the beta software on your Archer BE550 V1, then check if Linksys PAP2T adapter connects to the internet properly. You can download the beta firmware directly from the thread below:
Devices with 10/100Mbps Connections Lose Internet After Updating Archer BE550 V1 Firmware to 1.1.1
- Copy Link
- Report Inappropriate Content
Hi @Kevin_Z !!
If i connect laptop with 100MBps Half duplex
After install Beta firmware
Now Linksys PAP2T is viewed by BE550.
Thanks in advance.
Best regards,
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi @Baxajaun,
There is no clear feedback indicating that the Linksys PAP2T is not compatible with the TP-Link router. You can try to set it up referring to Linksys PAP2T VoIP Adaptor Setup
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi @Joseph-TP !!!
I've connected Linksys PAP2T adapter to ZTE ZXHN H196Q, and ZTE device TO BE550. All is ok.
But if i connect PAP2T directly to BE550, BE550 doesn't it.
Thanks in advance.
Best regards,
- Copy Link
- Report Inappropriate Content
Hi@Baxajaun,
May I know what is the network topology of your devices?
Is it looking like this:
ZTE ZXHN H196Q——BE550
|
|
PAP2T adapter
Do you want to remove the ZTE ZXHN H196Q and build a connection between BE550 and PAP2T separately? If so, after replacing the new router, you usually need to reconfigure the Linksys PAP2T. It is recommended that you consult the Linksys PAP2T support to confirm how to reconfigure the Linksys PAP2T?
- Copy Link
- Report Inappropriate Content
Hi @Joseph-TP !!!
Thanks for your response.
This is the network topology now:
BE550 ---- ZTE ZXHN H196Q ---- PAP2T adapter
But if change topology to:
BE550 ---- PAP2T adapter
BEE550 don't detect PAP2T adapter.
Thanks in advance.
Best regards,
- Copy Link
- Report Inappropriate Content
Hi @Baxajaun,
Are you testing the Ethernet port of the PAP2T adapter to see if it is working properly? Have you tested other clients on the same port?
Is the PAP2T adapter assigned an IP address? Could you provide your test steps and screenshots of the results?
Please go to the BE550 management page to check the Ethernet status page. Go to Network Map--Archer BE550--Ethernet Status. If possible, please provide screenshots.
Please check the BE550 DHCP list to see if the PAP2T adapter is in the client list and the corresponding IP address. Go to Advanced--Network--DHCP server--DHCP client list.
- Copy Link
- Report Inappropriate Content
Hi @Joseph-TP !!!
Sorry for delay.
Here you are :
PAP2T connect on Port 1
ZTE H196Q connected on PORT 1 and PAP2T connected to ZTE H196Q
Thanks in advance.
Best regards
- Copy Link
- Report Inappropriate Content
Thank you so much for all the details.
Is it possible to modify the 10/100 M RJ-45 network interface settings on the Linksys PAP2T adapter? If possible, please try to fix it on 100Mbps and then check if it can get a valid connection from the BE550 directly.
If possible, could you please try to modify the link speed on a wired computer to 100Mbps, connect it to one of the 2.5G LAN posts of the BE550, then check if the wired computer can connect to the internet properly. You can refer the steps provided in this article to modify the adapters settings on the Windows computer:
https://community.tp-link.com/en/home/forum/topic/723366
Updated on Feb 14, 2025:
Our development team also provides beta software to address this issue. Please upgrade and install the beta software on your Archer BE550 V1, then check if Linksys PAP2T adapter connects to the internet properly. You can download the beta firmware directly from the thread below:
Devices with 10/100Mbps Connections Lose Internet After Updating Archer BE550 V1 Firmware to 1.1.1
- Copy Link
- Report Inappropriate Content
Hi @Kevin_Z !!!
I've connected a laptop to BE550-
10MBps Full duplex
---------------------------
100Mbps Full duplex
----------------------------
1000 MBps Full duplex
-------------------------------
I don't know BEE550 don't see Linksys PAP2T connected directly.
TIA!!!
Best regards,
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 374
Replies: 15
Voters 0
No one has voted for it yet.