Early Access Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection
This Article Applies to:
Archer BE800 V1
New Features and Modifications:
- Newly support 3-band (2.4GHz + 5GHz + 6GHz) MLO connection.
- Newly support EasyMesh in AP mode.
- Newly support DoH/DoT.
- Enhanced system stability and security.
Firmware Download
Before the Upgrade
(1) Please be sure you have read the Beta Test Agreement before upgrading the pre-release firmware!
(2) For the sake of insurance, it's always recommended to save a copy of the router Backup Config file before upgrading or downgrading.
(3) You may follow the guide to upgrade the firmware of your router. How to Upgrade the Firmware on the TP-Link Wi-Fi Routers.
(4) This pre-release firmware for Archer BE800 V1 can be applied to all versions (EU/US/JP/TW/etc.).
(5) This version of software can be degraded to the previous version.
(6) To use the new 3-band MLO connection, both the router and client device must support Wi-Fi 7 and 3-band MLO. Please note that most Wi-Fi 7 smartphones and network adapters may only support 2.4GHz + 5GHz or 2.4GHz + 6GHz when connecting to the MLO Network.
Direct Firmware Download link:
Archer BE800_V1_1.1.99 Build 20241126 (Pre-release Software)
Additional Information
As always, we value your feedback. If somehow you encounter an issue during or after the router firmware upgrade, it's suggested to comment below with the following info. Your input helps us continue to improve and provide the best possible products and support.
- Detailed issue description, and provide more information on the specific conditions that seem to trigger the problem.
Related Articles:
EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller
Wi-Fi Routers Support DoH and DoT Network
What is WiFi 7’s Multi-Link Operation (MLO)?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Kevin_Z wrote
Does this mean there will be no internet at all?
-> it connects after a while at 1g
Are you saying when the Intel 10G SFP module is connected to the 10 Gbps SFP+ port, and a client device is connected to port 3, there won't be connectivity on the SFP+ port?
Yes it shows 0mbps on the BE800 in AP mode and link light is off on the client. In system log
It shows 2.5 port 1-5 off, combo port off.
I rolled back to 1.1.6 and it started working again.
- Copy Link
- Report Inappropriate Content
@Kevin_Z Does it support DoH/DoT thru IPV6 servers ?
- Copy Link
- Report Inappropriate Content
NPGrey wrote
Are you saying when the Intel 10G SFP module is connected to the 10 Gbps SFP+ port, and a client device is connected to port 3, there won't be connectivity on the SFP+ port?
Yes it shows 0mbps on the BE800 in AP mode and link light is off on the client. In system log
It shows 2.5 port 1-5 off, combo port off.
I rolled back to 1.1.6 and it started working again.My config, BE800 main connected to BE800 in AP Mode with 10g Ethernet connected to a omada switch via sfp+
Just confirm again, the topo is like the below:
Main BE800 (Router Mode) --- Omada Switch via SFP+ --- BE800 (AP Mode)
What device were you connected to port 3 on the 2nd BE800 when the issue happened? Have you confirmed if changing with another client device would make a difference?
I will report this issue to the engineering team for further analysis. If you have more details, please add up. Thank you very much.
- Copy Link
- Report Inappropriate Content
The topology is
BE800 main --- Ethernet --- BE800 AP mode --- omada via sfp.
I have not tried other devices, I will reinstall the beta and try with other devices and post the system log a bit later
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
hi @Kevin_Z
2024-12-03 13:34:16 Led Controller INFO [17456] Start to run INET_UP
2024-12-03 13:34:16 Led Controller INFO [17456] Start to run INET_OFF
2024-11-26 00:00:49 Led Controller INFO [17456] Start to run wanlancombo_OFF wanlan10g_ON lan2g5_1_OFF lan2g5_2_OFF lan2g5_3_OFF lan2g5_4_OFF
2024-11-26 00:00:49 Led Controller INFO [17456] Start to run INET_OFF
2024-11-26 00:00:43 UPnP INFO [19688] Service start
2024-11-26 00:00:43 UPnP INFO [19688] Service stop
2024-11-26 00:00:43 Remote Management INFO [19356] Service stop
2024-11-26 00:00:43 Led Controller INFO [17456] Start to run INET_OFF
2024-11-26 00:00:43 Traffic Statistics INFO [14185] stats reset
2024-11-26 00:00:42 Traffic Statistics INFO [14185] stats off
2024-11-26 00:00:41 Led Controller INFO [1377] Start to run STATUS_ON
2024-11-26 00:00:38 Led Controller INFO [1377] Start to run GENERAL
2024-12-03 13:34:16 Led Controller INFO [17456] Start to run INET_UP
2024-12-03 13:34:16 Led Controller INFO [17456] Start to run INET_OFF
2024-11-26 00:00:49 Led Controller INFO [17456] Start to run wanlancombo_OFF wanlan10g_ON lan2g5_1_OFF lan2g5_2_OFF lan2g5_3_OFF lan2g5_4_OFF
2024-11-26 00:00:49 Led Controller INFO [17456] Start to run INET_OFF
2024-11-26 00:00:43 UPnP INFO [19688] Service start
2024-11-26 00:00:43 UPnP INFO [19688] Service stop
2024-11-26 00:00:43 Remote Management INFO [19356] Service stop
2024-11-26 00:00:43 Led Controller INFO [17456] Start to run INET_OFF
2024-11-26 00:00:43 Traffic Statistics INFO [14185] stats reset
2024-11-26 00:00:42 Traffic Statistics INFO [14185] stats off
2024-11-26 00:00:41 Led Controller INFO [1377] Start to run STATUS_ON
2024-11-26 00:00:38 Led Controller INFO [1377] Start to run GENERAL
this is from the system log
- Copy Link
- Report Inappropriate Content
Thank you very much for the detailed information.
I've reported this issue to the development team, and they will analyze it as soon as possible.
- Copy Link
- Report Inappropriate Content
Any chance the Add IPV6 proper rfc6603 support was added ?
+1 for the Re:BE800 SFP 2.5G Mode ?
And dnsmasq 2.83 update please ?
Thanks.
- Copy Link
- Report Inappropriate Content
@benoitm974 Out of 8 feature requests from users on the forum, some which have users' votes, only 1 was taken into account over 8 month. From my perspective is is even more frustrating from a brand to say they will do something, open a community forum and never commit ...
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 3153
Replies: 51
Voters 1