Archer C64 SMARTCONNECT + mesh problems
Hi there,
Here's my area, about 80square meters
distance between routers is 11 meters.
one ssid, smartconnect on, transmit power LOW
with two AX23's routers and ethernet backhaul easymesh i had no problems with wifi:
wireless clients (only wifi5 ac) always have 5ghz AC connect in zone 2,3,4,5
2.4ghz connect ONLY in zone 1,6 (wery very thick walls) - client always switch to 2.4ghz and immediately switching back to 5ghz in other zones.
everything is fine, perfect mesh, perfect roaming MAIN-SATELLITE and back.
(i use android samsung m34, a50, s20, xiami... and iphone14. wifianalyzer to see which router is now connected)
BUT
REPLACING satellite ax23 to archer C64 (just connected power+lan+updated to last firmware 1.13.15)added it to mesh:
once ANY client is connected to satellite, it always keep connect to C64 with 2.4ghs speed in zone 1,2,3,4,5.
even when main router signal is much better:
On screen you can see, my mobile is near main ax23 its 5ghz signal is much stronger but still is connected to SATELLITE 2.4GHZ with-57db.
only when 2.4ghz signal drop below -70db in "zone 6". it will roam to main ax23 2.4ghz and immediately switch back to 5ghz in zone 4-5
ax23 stiching 2.4-5-2.4-5ghz no problems
C64 doesn't want to let go his clients, always keeping slow 2.4ghz connect
maybe bug in 802.11v so it haveonly "ONE WAY" to 2.4?
Turned ON wifi near ax23:
Connected to 2.4 ghz :CA
ROAM SCAN RESULT CONNECTED TO :C9 WIFI 5 !!! OK 802.11V WORKS ON AX23
turned WIFI OFF
turned WIFI ON NEAR C64 zone and it always keep 2.4ghz connection:
Connected to 1A 2.4
ROAM SCAN RESULT 24-2F-D0-93-F2-1A IT TRIGGERS TO ROAM to THE SAME 2.4GHz :)
but it should trigger connect to 24-2F-D0-93-F2-1C which is 5GHz !!!
BUG!
this router does not work like it should
waiting for answer and beta firmware :)
Smartconnect on ax23 work perfect, moving clients to 2.4 and back to 5ghz when signal is good
but smartconnect in C64 is annoying. it always keep 2.4 even when 5ghz signal is very good
c64 router every minute trigger client to connect same 24-2F-D0-93-F2-1A it is already connected to it:)))
it must connect to 24-2F-D0-93-F2-1C (5ghz network)
@Marvin_S Thanks for reply.
changed tx power to High
Turned on wifi on mobile and connected to C64 5ghz :1C good.
Went away to drink a cup of tea :)
Smartconnect moved me to 2.4ghz :1A, thanks for it.
Went back and stand in front of C64:
2.4ghz signal -20dbm
5ghz signal -21dbm
Smartconnect, HELLO???
no answer
no move to 5ghz
wait few minutes no change
Before u say that this is my mobile client samsung phone problem,
I answer : archer AX23 does this job
@Marvin_S ? no mails no questions
archer ax23 main ax23 satellite smartconnect works perfect.
archer ax23 main c64 satellite smartconnect works bad
archer c64 main c64 satellite smartconnect works bad.
my devices still are on 2.4ghz even when 5ghz signal is strong.
smartconnect dont work properly
id like to call it smartslownect
