Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Dual WAN connected to different routers supported

< Deco

Dual WAN connected to different routers supported

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Dual WAN connected to different routers supported

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AstralWarrant

2024-03-22 16:58:19 - last edited 2024-10-25 12:00:08

Posts: 3

Helpful: 2

Solutions: 0

Stories: 0

Registered: 2024-03-22

Dual WAN connected to different routers supported

2024-03-22 16:58:19 - last edited 2024-10-25 12:00:08

Tags: #Presales

Model: Deco BE63

Hardware Version:

Firmware Version:

Is it possible with Deco BE63 (or any TP-Link product) to setup a network with dual WAN links (from different ISPs)

with the WAN links piugged into different units?
I only need failover, I don't need link bonding or anything like that.

ie. WAN1 <--> (Deco1) <--backhaul link--> (Deco2) <--> WAN2

Note that it is important that (Deco1) and (Deco2) are in different rooms from each other.

4 Reply

ImtiazAli

LV4

2024-03-23 08:16:04

Posts: 607

Helpful: 281

Solutions: 33

Stories: 0

Registered: 2021-03-21

Re:Dual WAN connected to different routers supported

2024-03-23 08:16:04

@AstralWarrant Check out tp-link ER605

Just a M4 (2-pack) user who regrets buying it

Nukos

LV2

2024-03-23 08:34:25 - last edited 2024-03-23 08:34:44

Posts: 20

Helpful: 11

Solutions: 2

Stories: 0

Registered: 2023-07-29

Re:Dual WAN connected to different routers supported

2024-03-23 08:34:25 - last edited 2024-03-23 08:34:44

@AstralWarrant

I was thinking something like this also. But my diagram goes like this. ISP1 and ISP2 connected to the 2 LAN/WAN of the MAIN AP Deco. I don't know if this kind of thing will work.

AstralWarrant

LV1

2024-03-24 21:37:55

Posts: 3

Helpful: 2

Solutions: 0

Stories: 0

Registered: 2024-03-22

Re:Dual WAN connected to different routers supported

2024-03-24 21:37:55

@ImtiazAli, it doesn't look like the TP-Link ER605 will work for what I need.

I'm looking for a mesh setup where I can hook up the WAN connection (to the ISP) to different units that are in different rooms from each other.

David-TP

2024-03-25 09:48:16

Posts: 12841

Helpful: 1806

Solutions: 1298

Stories: 9

Registered: 2020-04-14

Re:Dual WAN connected to different routers supported

2024-03-25 09:48:16

@AstralWarrant

@Nukos , Hi, nice to see you again.

Deco doesn't support connecting two WAN connections to its different Ethernet ports, or two WAN connections to different Mesh Units.

We might need to add an additional router that supports Link Failover.

How to use Deco with two ISPs?

While as for a hybrid Mesh system with general Deco and Deco_4G/5G, It is planned to support a failover connection like the following:

Deco X73-DSL works as the main Deco in DSL modem router mode and Deco X50-5G works as a satellite. when the DSL connection failed, Deco X50-5G could work as a 5G router to provide a backup mobile service.
Deco X73-DSL works as the main Deco in wireless router mode and Deco X50-5G works as a satellite. when the Ethernet WAN connection failed, Deco X50-5G could work as a 5G router to provide a backup mobile service.

Thank you very much and best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Dual WAN connected to different routers supported

Dual WAN connected to different routers supported

Information

Voters 0

Tags