Home Network Community > 5G/4G Wi-Fi Routers/MiFi > Cannot enable DMZ host feature on NX510v router
< 5G/4G Wi-Fi Routers/MiFi

Cannot enable DMZ host feature on NX510v router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Cannot enable DMZ host feature on NX510v router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Cannot enable DMZ host feature on NX510v router
Cannot enable DMZ host feature on NX510v router
2023-12-11 12:50:25 - last edited 2023-12-12 09:49:24
Tags: #NAT

Situation

I want to forward the traffic from WAN to a particular device on my LAN. For this I tried to enable the DMZ feature from the Advanced > NAT Forwarding menu.

 

Expected behavior

The settings should take effect without errors. I would be able to reach the configured host from the Internet.

 

Actual behavior

A warning message appear with this text below:

CWMP Function conflict with the DMZ Host. DMZ Host will fail at cwmp port. Click Yes to continue.

 

 

Even if I click on yes, the function does not have the expected effect.

 

Additional Notes

I've tried so far:

  • I checked for firmware updates, but the current is the latest.
  • I did a factory reset, but same warning comes up.
  • The Remote Management function is disabled.
  • This is not an Archer router. I selected that, becase NX510v is not offered in the model selector and the field is mandatoy.

 

 

Does anyone else have the same problem? How can I get this working?

 

  0      
 
  0      
 
#1
Options
4 Reply
Re:Cannot enable DMZ host feature on NX510v router
2023-12-12 09:53:33

  @Geza83 

 

Hi, 

 

NX510v is a model for ISPs only, and we don't have much information about it, and usually ISPs might have default CWMP Settings on the product.

Besides, you could check Internet IPv4 address on the NX510v to see if it is a public IP address or not, if not, it means you are behind CGNAT thus the DMZ will not work, you will need to contact your ISP to check if they could assign you a public IP address.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Cannot enable DMZ host feature on NX510v router
2023-12-12 15:28:04
Hi @Sunshine, Well, I've already turned to my ISP's support channel, but they said that the router is tested for "regular usage" and don't give support beyond that. They suggested to do factory reset or get contact with the manufacturer. Since factory reset did not make a difference, I wrote my post here. I've checked the dynamic IPv4 address I got from ISP, it responds to ping from the Internet, so that should not be a problem. Though I have no idea what CWMP is.
  0  
  0  
#3
Options
Re:Cannot enable DMZ host feature on NX510v router
2023-12-13 02:37:59

  @Geza83 

 

You could go to Advanced > System Tools > CWMP Settings page to see if you can see it and disable it for a test.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options
Re:Cannot enable DMZ host feature on NX510v router
2023-12-13 09:31:55

  @Sunshine 

 

Unfortunately I don't see such menu there.

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 927

Replies: 4

Tags

NAT
Related Articles
 Deco M5 DMZ Host
2453 0
NX510v device password
377 0
NX510V High Ping
57 0
 Cannot connect to Host
124 0
 Port forwarding/DMZ host not working on my archer C7
1050 0
 Error code: 4624 Function conflict with the DMZ Host
1212 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.