Home Network Community > Deco > Speed issues after switching to router mode - gigabit to megabit speeds
< Deco

Speed issues after switching to router mode - gigabit to megabit speeds

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Speed issues after switching to router mode - gigabit to megabit speeds

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Speed issues after switching to router mode - gigabit to megabit speeds
Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-06 22:50:18 - last edited 2023-11-06 23:10:56
Tags: #Deco Ethernet Backhaul #Network Connectivity #Access Point Mode
Model: Deco X60  
Hardware Version: V3
Firmware Version: 1.2.4 Build 20230601 Rel. 37750

Hi,
I've changed my setup to use deco as main router, but am experiencing speed drops on LAN from 900+ to 90+ on my 2nd Deco, but the rest of the devices are still 900+
All wires cat6
Seems like it dropped from gigabit to megabit speeds

Attached the setup changes below.
When i change it back to setup A the speeds are back up again

WIFI speeds are still 500-700+ on iPhone/iPad/Apple TV around the house 

Also tried marking device as high priority

 

Multiple devices connected to all switches.

 

Model: Deco X60

Hardware Version: V3.0

Firmware Version: 1.2.4 Build 20230601 Rel. 37750

 

Setup

 

 

 

  0      
 
  0      
 
#1
Options
12 Reply
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-07 07:08:28

  @amornn 

Hi, welcome to the community.

Have you also tested the wireless speed from the 2nd Deco X60 here:

I see you also used the TP-Link switch and can I have its model number?

Have you checked the Ethernet port indication? is it green or orange?

Since the 3rd Deco X60 could still get 900+, I think the ports 1+2 should be fine. Have you tried to connect the laptop and TV to other Ethernet ports of the switch?

Thank you very much and best regards.

Deco Monthly Recap- Check What's Currently Going on With Deco Deco X50/X55_V1_1.6.0 Open for Test! Deco APP 3.8.36 Greatly Optimized Network Management Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-07 07:30:16

  @David-TP hi, yes WiFi speeds are still high. 
Will try direct Ethernet from deco 2 to pc.

will check model number once I'm home. 
 

  1  
  1  
#3
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-07 07:45:13

  @amornn 

Thank you and will wait for your updatelaugh.

Deco Monthly Recap- Check What's Currently Going on With Deco Deco X50/X55_V1_1.6.0 Open for Test! Deco APP 3.8.36 Greatly Optimized Network Management Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#4
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-08 06:10:26 - last edited 2023-11-08 06:14:03

  @David-TP 
Switch Model: TL-SG108(un) v6.0

Light is green

Tried switching ports around, still same speed. (Without switching ports, in setup A i was getting gigabit).

Tried deco to PC lan directly speed went up to gigabit. moved it back to switch and it went down again.

With setup A to Setup B, I didn't change any ports. took wire going from modem to router to modem to Deco and changed main deco to router mode.

 

 

  0  
  0  
#5
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-08 06:11:27

  @amornn Can you show screenshots of the mesh (how Deco are logically interconnected) in Router and in AP mode?

What is your QOS setting?

  0  
  0  
#6
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-08 06:16:47 - last edited 2023-11-08 06:20:24

 
Connected the same way, just moved wire from asus to deco and changed deco to 

 

@yves_b 

  0  
  0  
#7
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-08 06:17:24

  @David-TP Is it a good idea, in Router mode, to connect wired devices on a switch used for Ethernet backhaul?

  0  
  0  
#8
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-08 06:23:40

  @yves_b @David-TP 

 

Drew the initial setup image incorrectly, both decos going through main switch

 

 

  0  
  0  
#9
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-08 06:25:22

  @amornn I suggest testing with QOS disabled.
I do not understand how both satellite Decos could establish an Ethernet link with the main Deco.  To me, it contradicts your network map.

  0  
  0  
#10
Options
Re:Speed issues after switching to router mode - gigabit to megabit speeds
2023-11-08 06:35:47

  @yves_b Tried, didn't work

  0  
  0  
#11
Options
12

Information

Helpful: 0

Views: 868

Replies: 12

Tags

Deco Ethernet Backhaul Network Connectivity Access Point Mode
Related Articles
Switching Deco X60 to "Wireless Router" Mode Makes Connectivity Unstable
918 0
Switching Deco x20 to WiFi Router Mode
2995 0
TL-MR100 automatic switching from wireless Router Mode to 3G/4G Router Mode
482 0
Switching to router mode from access point mode?
611 1
On switching to access point mode, router mode wifi network stays available
788 0
How to optimize wireless settings for TP-Link VR600 router and Deco system in AP mode
458 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.