Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router
Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router
2023-10-18 18:54:26 - last edited 2023-10-19 08:57:01
Model: Archer C55  
Hardware Version: V1
Firmware Version: 0.9.1 3.16 v0001.0 Build 170614 Rel.32665n

Greetings
I recently thought of bringing my old tplink router back to life when I needed wired internet for some of my devices

I connected the tplink router to the root router via WDS and was able to use the LAN ports successfully.

But the issue with this was that the LAN port are 100mbit/s , this is when I came across people configuring the WAN port as a nornal LAN
On this I consulted the manual and there was an option to use the WAN as a normal LAN (Image attached)
So can any of the smart folk here help me with this and whether it would be possible or not
I also considered OpenWRT but unfortunately this router is not supported 

Image ref : Manual -> https://static.tp-link.com/1910012259_Archer%20C55_V1_UG.pdf Chapter 1 Pg 5

WAN as Ethernet

  0      
  0      
#1
Options
5 Reply
Re:Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router
2023-10-18 19:17:24 - last edited 2023-10-19 08:57:01

  @Shaup 

 

When using WDS on Archer C55 you can't use its gigabit WAN port to connect a LAN device because the C55 is still in router mode.

Archer C55 has an access point mode though and its gigabit WAN port can be used for an uplink to the main router - details (Case 1).

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  3  
  3  
#2
Options
Re:Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router
2023-10-19 04:49:15

  @terziyski 

But I am already using the router in WDS mode and I am able to access the lan ports
It is not possible for me to physically connect both the routers. I want to know how to repurpose the WAN port as a regular LAN port 

  0  
  0  
#3
Options
Re:Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router
2023-10-19 07:59:28

  @Shaup 

 

Hi, as @terziyski mentioned, when using WDS on Archer C55, it is still on router mode thus the Gigabit WAN Port acts as WAN port only and cannot be used as LAN port.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options
Re:Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router
2023-10-19 08:56:45 - last edited 2023-10-19 08:57:20

  @Sunshine 

So is there a way to use the WAN port as LAN port without physically connecting the two routers ??

  0  
  0  
#5
Options
Re:Using the Gigabit WAN port as a normal LAN on the Archer C55 AC 1200 router
2023-10-19 10:59:38

  @Shaup 

 

No, there's no way to do that when using WDS.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#6
Options