Home Network Community > Wi-Fi Routers > EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
< Wi-Fi Routers

New Release EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW

1161718...

New Release EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW

907 Reply
Re:EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
2023-07-13 07:58:50

 

klipse wrote

  @Kevin_Z 

 

I posted a while ago under the "App" section on your website, no one has replied to date, can you advise please?

 

Thanks

 

https://community.tp-link.com/en/home/forum/topic/612160

 

@klipse I just replied to you in the mentioned thread. Please check.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#170
Options
Re:EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
2023-07-13 08:13:41

 

g3n0 wrote

I was finally able to test EasyMesh with Ethernet backhaul on two Archer C80s. Both are HW v2.20, so I upgraded the FW to the latest.

 

First I connected all devices to the main C80, then defined the secondary C80 as a satellite router from the web GUI.

 

First, the satelite device was not found by the main router, so I connected it just to power near the main unit and this helped. I got one mesh device, but over wireless backhaul.

Turned the satelite unit off, connected it with a RJ45 to the WAN port and powered it on. After not so short time, the main router found the satelite in the EasyMesh settings, full connection which seemed over cable. So far so good, BUT whenever the satellite router is ON, the connection get very laggy and unstable, I get warning messages on most of the internet dependend software on my desktop, which is also connected over rj45 to the main router. Whenever I switch it off - internet connection works very smooth.

 

Any ideas what I might try to work around this slowness? @Kevin_Z @Thom_NL 

 

@g3n0  Please try resetting the satellite C80 to factory defaults, then connect one of its LAN ports to the LAN port of the main C80 (LAN - LAN), check again if they can build up the EasyMesh Ethernet Backhaul automatically. You can check the connection status either on the web GUI or via Tether App.

 

After they build up the mesh network successfully, please check again if you can get the desired speed.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#171
Options
Re:Early Release Firmware Adding EasyMesh Ethernet Backhaul for Archer C80/C64/A8
2023-07-13 09:21:16

  @Kevin_Z,

 

I'm afraid that the firmware page's aint up to date for the BR version.

 

For the EU ( EN ) there is more available wink

 

 

Regards,

 

Thom 

  0  
  0  
#172
Options
Re:Early Release Firmware Adding EasyMesh Ethernet Backhaul for Archer C80/C64/A8
2023-07-13 10:22:27

@Thom_NL 

 

Which firmware do you refer to?

 

BTW, our development team has provided a pre-released version of firmware for Archer C80, and I have just published it below, you can check if you're interested:

Pre-Released Firmware Supports DoH and IoT Network for Archer C80 is Ready for Trial

 

Do let me know if this version meets your requirements or if there is an issue with it. I'm always happy to assist.  

 

Please make sure you're tagging me or Sunshine if you want a direct response timely.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#173
Options
Re:Early Release Firmware Adding EasyMesh Ethernet Backhaul for Archer C80/C64/A8
2023-07-13 11:11:27

 hi @Kevin_Z & @Sunshine 

 

I did refer to the BR firmware, looking at the support page it lacks a lot  ( versions of the FW )

 

Thanks for the Beta link, i wil give it a go wink

 

 

regards,

 

Thom

  0  
  0  
#174
Options
Re:Early Release Firmware Adding EasyMesh Ethernet Backhaul for Archer C80/C64/A8
2023-07-13 11:41:00

  hi @Kevin_Z,

 

The name of the firmware seems to have isseus ( c80v2-up-noboot_2023-07-05_18.52.09.bin )

I renamed it to c80v2-2023-07-05. bin and that worked.

 

The watermark in this Beta spoils the joy of it.

 

The sattelite C80 does'nt update after updating the main??

 

 

Regards,

 

Thom

  0  
  0  
#176
Options
Re:Early Release Firmware Adding EasyMesh Ethernet Backhaul for Archer C80/C64/A8
2023-07-13 13:47:39 - last edited 2023-07-13 13:51:24

  @Thom_NL @Kevin_Z 

 

Alright, update here! Finally the Ethernet backhaul worked enlightened

 

First I unplugged the cable from the satellite -> the EasyMesh connection persisted, but the warning messages about unstable connection disappear. Icon in the GUI did not changed. So it looks like it was using wireless backhaul the whole time. Seems like the issue with the unstable connection is a result from connecting the satellite router over cable to the main unit, when it is connected over wireless to it. It does not mater if the cable is connected to the LAN or the WAN port = same issue with unstable connection. I guess the main router goes into some kind of a loop when the EasyMesh wireless backhaul is enabled to a satellite while the cable is connected as well. It would have been nice to make a seemless switch.

 

Also, the main router seems to be remembering the MAC address of the satellite and type of the EasyMesh backhaul connection. I reseted the satellite router multiple times to factory defaults, switched between main and satellite mode - nothing helped. The sattelite always connects to the main unit over wifi :((

 

Lickily, I bought 3 pieces. So I unpacked my 3rd C80, updated the FW to 1.12.1 Build 221212, connected it LAN to LAN with the main unit and VOILA, it efffin worked!!!

 

Attaching a screenshot with the current status:

 

  4  
  4  
#177
Options
Re:EasyMesh Routers Support Building a EasyMesh Network via Ethernet Backhaul NOW
2023-07-13 14:49:54

  @Kevin_Z thanks you for the answer.

 

For now, I will continue with the Wi-Fi(easymesh) connection between the routers. Are there any plans to support Ethernet backhaul on AX53 and AX10?

  0  
  0  
#178
Options
Re:Early Release Firmware Adding EasyMesh Ethernet Backhaul for Archer C80/C64/A8
2023-07-13 21:29:56
would love to see this for the AX90 and RE815X as well
  0  
  0  
#179
Options
Re:Early Release Firmware Adding EasyMesh Ethernet Backhaul for Archer C80/C64/A8
2023-07-14 03:29:19

 

Thom_NL wrote

  @Kevin_Z,

 

I'm afraid that the firmware page's aint up to date for the BR version.

 

For the EU ( EN ) there is more available wink

 

 

Regards,

 

Thom 

 

@Thom_NL I checked the firmware release on the BR website, and it seems the firmware is up-to-date. For example, Archer C80(BR)_V1_1.12.10 Build 230208 is the latest version for C80 V1 as of now.

 

Can you post a direct link if you find there is firmware missing on the BR website? Thank you very much.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#180
Options
1161718...

Tags

EasyMesh Firmware Update Highlighted Thread EasyMesh Ethernet Backhaul
Related Articles
EasyMesh not on AX53
2006 0
What is EasyMesh and how does it work with TP-Link routers and extenders?
86638 19
EasyMesh Configuration
681 0
How to Build an Ethernet Backhaul Using Two EasyMesh Routers
12866 9
Archer C7 V5 - EasyMesh Support
1283 0
Official EasyMesh Firmware for Archer AX55 is NOW available
36197 17
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.