MR600 V2 Carrier Aggregation Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MR600 V2 Carrier Aggregation Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
MR600 V2 Carrier Aggregation Issue
MR600 V2 Carrier Aggregation Issue
2021-06-01 09:37:26
Model: Archer MR600  
Hardware Version: V2
Firmware Version: 1.3.0.0.9.1 v0001.0 Build 210208 Rel.61056n

I am using MR600 V2 with jio sim in India.

B3 + B5 is working.

B40 + B40 is also working, which is good.

 

B3/B5 + B40 is not working. For that case only giving priority to B40 and it is working as B40 + B40. If the B40 is down or poor signal then your internet will be die. Also when file is uploading carrier Aggregation is not working.

  0      
  0      
#1
Options
3 Reply
Re:MR600 V2 Carrier Aggregation Issue
2021-06-04 09:53:27

@Smandal900 

 

Whether the bands aggregate or not, and how these bands are aggregated with each other, are decided by the cellular tower, the router only sends the request to the cellular tower in your area.


Just to confirm, can you get band 3 / band 5 + band 40 on another 4G router, or can you get the two aggregated on the phone?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:MR600 V2 Carrier Aggregation Issue
2021-06-04 16:26:29

@Kevin_Z 

 

After restart or band selection b3 + b40 is working for 30 to 50 seconds. After that it is permanently switching b40. That means in my area b3+b40 is working. One of youtuber also mention that mr600 v1 is working b3+b40, but V2 is not working.

  0  
  0  
#3
Options
Re:MR600 V2 Carrier Aggregation Issue
2021-06-08 03:36:09

@Smandal900 

 

We have reported the issue to the support engineers, they will likely reach out to you via email to continue to troubleshoot your issue.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options