static routes not applied after reboot

Kevin_Z

2021-01-20 09:17:55

Posts: 21569

Helpful: 5031

Solutions: 2542

Stories: 21

Registered: 2018-12-24

Re:static routes not applied after reboot

2021-01-20 09:17:55

@MiCHiCZ

Can we have the detailed scenario about the static route settings on the AX50? And please share with us the setting screenshot on the AX50, we can then check if there is anything wrong with that.

BTW, what is the network diagram/layout?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

0

#2

MiCHiCZ

LV1

2021-01-20 19:10:18

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-01-20

Re:static routes not applied after reboot

2021-01-20 19:10:18

@Kevin_Z

i have multiple raspberrypis connected to router via LAN. they are connected to multiple customer VPNs (via OpenConnect, OpenVPN, FortiVPN)

.254 - router

.253 - rpi1

.250 - rpi2

.251 -rpi3

everything works fine, no interference in subnets, but if i reboot the router, only routes on interface WAN are created, after switching bulb off/on the static route table fills up and everything works fine again

0

#3

Kevin_Z

2021-01-21 03:22:29

Posts: 21569

Helpful: 5031

Solutions: 2542

Stories: 21

Registered: 2018-12-24

Re:static routes not applied after reboot

2021-01-21 03:22:29

@MiCHiCZ

If that is the case, we would like to follow up on your case via email. Please check your inbox.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

0

#4

MiCHiCZ

LV1

2021-04-12 22:24:47

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-01-20

Re:static routes not applied after reboot

2021-04-12 22:24:47

finally, i reproduced it, it's caused by ipv6, after disabling/enabling the ipv6, the static routing table is flushed and not applied again

0

#5

Kevin_Z

2021-04-13 06:28:24

Posts: 21569

Helpful: 5031

Solutions: 2542

Stories: 21

Registered: 2018-12-24

Re:static routes not applied after reboot

2021-04-13 06:28:24

@MiCHiCZ

Can you please report this directly to the engineers by replying to their email, they will then help confirm if there is an issue?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

0

#6

static routes not applied after reboot

static routes not applied after reboot

Information

Voters 0

Tags