Home Network Community > DSL Modem Routers > Archer VR400 v2 / LAN Port 4
< DSL Modem Routers

Archer VR400 v2 / LAN Port 4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR400 v2 / LAN Port 4

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer VR400 v2 / LAN Port 4
Archer VR400 v2 / LAN Port 4
2020-10-31 16:12:03
Model: Archer A10  
Hardware Version: V2
Firmware Version: 0.6.0 0.9.1 v0070.0 Build 200713 Beta.34548n

Hello,

 

i'm using Archer VR400 v2 which should have one por 1Gb speed which is port LAN4, but this port is not active , my connection type is DSL

 

i'm able to use port 1,2 and 3 but i need to connect my desktop with cable to get 1Gb speed. but port 4 not coming up.

 

Thanks.

  0      
 
  0      
 
#1
Options
8 Reply
Re:Archer VR400 v2 / LAN Port 4
2020-11-05 08:44:25

@bikoo 

Good day,

Thank you very much for your time and patience.

Did you check the Ethernet link speed and found out it was still limited to 100M/S?

Did you change a new cable, like cat 6 to have a look?

Have you tried to change the network adapter to 1G full-duplex mode to have a look:

Thanks a lot.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Archer VR400 v2 / LAN Port 4
2020-11-05 18:01:02

@Sunshine Thanks for your reply.

 

i'm using cat5 cable and the port not coming up. any reson behind that

  0  
  0  
#3
Options
Re:Archer VR400 v2 / LAN Port 4
2020-11-13 11:30:53

@bikoo 

Hi, thank you very much for your kind reply.

There might be some misunderstanding and I am really sorry about that.

I thought the issue was the speed on the LAN4/WAN was limited to 100m/s even though it claimed to be 1000m/s;

But actually, the device connected to the LAN4 was not detected and it seemed like no device connected to the LAN4/WAN, right?

And also the same laptop is working fine on LAN 1.2.3, just not LAN4?

Later, I would like to follow up on your case via email and please feel free to update more details on the email.

 

Thanks a lot.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options
Re:Archer VR400 v2 / LAN Port 4
2020-11-13 11:34:39 - last edited 2020-11-13 11:35:07

@Sunshine 

Hello,

 

yes what you are saying is correct and it's clear now from your side.

 

the PORT LAN4 not coming up at all, as i told you before i'm using CAT5

  0  
  0  
#5
Options
Re:Archer VR400 v2 / LAN Port 4
2020-11-20 08:34:01

@bikoo 

Verify if you have activated iptv on port 4, if so, the local adress of the port 4 should be 192.168.2.1

  0  
  0  
#6
Options
Re:Archer VR400 v2 / LAN Port 4
2020-11-20 08:43:00

@hajji66 

 

I didnt activate iptv 

hajji66 wrote

@bikoo 

Verify if you have activated iptv on port 4, if so, the local adress of the port 4 should be 192.168.2.1

 

  0  
  0  
#7
Options
Re:Archer VR400 v2 / LAN Port 4
2020-11-24 11:09:20

@bikoo 

 

Hi, as per your description, it seems that the LAN4 port might be faulty. You may confirm if this is still in warranty with the local support and try to get it replaced:

https://www.tp-link.com/support/contact-technical-support/#Hotline-Support

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#8
Options
Re:Archer VR400 v2 / LAN Port 4
2021-01-05 06:57:02
Thank you , i just did factory reset and the port is working fine
  0  
  0  
#9
Options

Information

Helpful: 0

Views: 1089

Replies: 8

Related Articles
Archer vr400 v2
2347 0
 Archer C6 v2 ethernet port 4 not working
532 0
ARCHER VR400 V2 FIRMWARE 0.5.0 0.9.1
1062 0
Archer vr400, can't upgrade from v2 to v3
1730 0
Archer vr400 ac1200 v. 2 dns disconnecting error
5777 0
 Archer VR400 port query
930 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.