Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Deco X20 configured as an "Access Point"

< Deco

Deco X20 configured as an "Access Point"

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco X20 configured as an "Access Point"

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Kestrel-Geek

2020-09-28 03:53:21 - last edited 2020-09-29 08:36:26

Posts: 2

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2019-07-26

Deco X20 configured as an "Access Point"

2020-09-28 03:53:21 - last edited 2020-09-29 08:36:26

Model: Deco X20

Hardware Version: V1

Firmware Version: 1.0.2 Build 20200630 Rel. 73505

I currently have the X20 v1.2 configured as access points on my network. I have the three X20's connected via wired CAT6 through a 5 port switch, then connected to a separate NIC on my pfSense network which is used to manage the network.The network has the usual WAN, LAN, and OPT1 which is my wireless access point. I'm not seeing anything in regards to WPA3 or WiFi 6 when I log into the Deco X20's? My question, is this available when configured as an "Access Point"? I know there is some options not available, but WPA3 and WiFi 6 should be working? So am I missing something, or is this normal?

1 Accepted Solution

David-TP

2020-09-29 08:36:22 - last edited 2020-09-29 08:36:26

Posts: 13384

Helpful: 1918

Solutions: 1452

Stories: 9

Registered: 2020-04-14

Re:Deco X20 configured as an "Access Point"-Solution

2020-09-29 08:36:22 - last edited 2020-09-29 08:36:26

@Kestrel-Geek

Hello, it is suggested to refer to the below FAQ (at the very last part) to enable the WPA3 on your Deco X20:

https://www.tp-link.com/support/faq/2943/

As for Wi-Fi 6, do you refer to 160MHz or something else? Deco X20 is advertised as 1200 Mb/s @5GHz band, which means it can support up to 80MHz channel width, not 160MHz.

For more specs, please refer to the official website:

https://www.tp-link.com/home-networking/deco/deco-x20/#specifications

Good days.

▶Deco BE65/85/95 New Firmware Versions Ready for Test ▶Deco M5 Newly Introduced Advanced Parental Control Features ▶Certain Programs and Service Can't be Loaded Properly on Deco M9 Plus_1.8.0 ▶Meet Us at CES 2025! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Recommended Solution

Kestrel-Geek

LV1

2020-09-29 17:28:32

Posts: 2

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2019-07-26

Re:Deco X20 configured as an "Access Point"

2020-09-29 17:28:32

@TP-Link_Deco

Thanks for the reply, I was able to find the WPA3 switch, but I'm a bit confused about the WiFi 6. I currently see 2.4GHz & 5GHz under the Wi-Fi Settings. The advertising for the Deco x20 shows it capable of 6 GHz:

https://www.tp-link.com/ca/home-networking/deco/deco-x20/

So what you're saying is the Deco x20 can only do 5GHz? or possibly I'm missing something.

Thanks in advance

Cheers

Kane

David-TP

2020-09-30 06:29:19

Posts: 13384

Helpful: 1918

Solutions: 1452

Stories: 9

Registered: 2020-04-14

Re:Deco X20 configured as an "Access Point"

2020-09-30 06:29:19

@Kestrel-Geek

Hello, sorry to make you confused.

Deco X20 does support 802.11ax (which we call Wi-Fi 6) for both 5GHz and 2.4GHz, and it supports up to 80MHz for the 5GHz and 40MHz for 2.4GHz, that means you can get up to 1200Mbps @5GHz and 574 Mbps @2.4GHz.

Deco X20 configured as an "Access Point"

Deco X20 configured as an "Access Point"

Information

Voters 0

Tags