Device not connecting to the nearest/fastest Deco M5
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi,
I recently purchased 2 units of Deco M5. I live in a 1860 sq.ft apartment. Both the Decos are present in the same floor. I see that my devices are NOT connected to the closest Deco and connected to the farthest Deco most of the times. This causes a considerable reduction in speed and it defeats the very purpose of installing a mesh.
To TP-Link R& D Team - Either improvise your algorithm to find the nearest Deco and connect seemlessly or let the user select the Deco M5 unit to which the device has to get connected to.
Please provide me with any known solution/workaround to overcome this issue temporarily.
Rgds,
Priya
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
still a few questions
1. Why is the version 1.5.1 while the current version is 1.5.3 x
2 when is the 1.6 released
3 when is the beta of 1.6 released.
4 The new version is not an enhancement on the current problem
- Copy Link
- Report Inappropriate Content
@TP-Link can the beta software be used for other units? I have a system of 3 that all came together but I'm not sure what one I actually have.
I have one router and two access points in a 1250 square foot apartment but my Nintendo switch will not move between access points.
I can manually connect to the closest Network but it won't go on its own somebody mentioned adjusting RSSI settings to make them lower so that it would force the device into roaming but I can't find those settings in my app.
I'm attaching an image of the devices and software versions I'm using. Any assistance would be greatly appreciated and I'd be happy to try out the beta software if it is compatible with my devices.
- Copy Link
- Report Inappropriate Content
Hi， Currently, there is no beta firmware that could force the device to roam to the closest Deco units for Deco M4;
And it is planned to allow manually selecting the closest Deco for devices to connect;
As for the Nintendo Switch, if it does not support the 802.11r protocol, it would ignore the roaming request sent by Deco and fail to roam between access points;
For more details, please refer to this link:
https://community.tp-link.com/en/home/forum/topic/180194
Thank you.
- Copy Link
- Report Inappropriate Content
@TP-Link Then, I have to ask just what is "roaming". The descriptions, in your ads, certainly imply that your device will switch to the nearest device as you move around.
- Copy Link
- Report Inappropriate Content
@TP-Link Have installed 1.5.1 firmware as suggested in this thread but devices then immediately updated to 1.5.3. Does this still have the network mapping improvements as it has regrettably not fixed this issue for me. :(
- Copy Link
- Report Inappropriate Content
Hi, there is a beta firmware 1.6.0 which added the feature to manually select the signal source.
But it could not be downgraded to 1.5.x firmware.
So if you want to try the 1.6.0 firmware, please have a check of your private message.
Thank you.
- Copy Link
- Report Inappropriate Content
@TP-Link the firmware that will supposedly allow us to choose source deco was announced here back in January. It has been over 6 months with no developments? Hope you can shed some info as to when the official firmware update will be released.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi Sir.. I am on firmware 1.5.0 now (Deco M4) and its not connecting to the nearest nodes. Please assist on this. TQ
- Copy Link
- Report Inappropriate Content
I know this thread is about the M5... I recently purchased the DecoX20 but I also have the same issue of my 3rd note deciding to connect to the main deco instead of the one that is closest to it. When can I expect a firmware update on the DecoX20 that sorts this issue too?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 15
Views: 44123
Replies: 42
Voters 2
