Home Network Community > 5G/4G Wi-Fi Routers/MiFi > MR600 how do i know if its connected to 4G+
< 5G/4G Wi-Fi Routers/MiFi

MR600 how do i know if its connected to 4G+

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MR600 how do i know if its connected to 4G+

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
MR600 how do i know if its connected to 4G+
MR600 how do i know if its connected to 4G+
2020-09-06 16:22:16 - last edited 2020-09-07 10:35:42
Model: Archer MR600  
Hardware Version:
Firmware Version:
I just purchased and installed MR600. im not sure if its using 4g+
my mobile phone is working on 4g+ so location is not a issue, also placed the router on best location to get higher signal strength possible. do i have to upgrade firmware to beta version?
 
 
 
im from chennain, india.
network provider: airtel
 
current Firmware Version: 1.2.0 0.9.1 v0001.0 Build 200511 Rel.44954n
  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:MR600 how do i know if its connected to 4G+-Solution
2020-09-07 00:27:49 - last edited 2020-09-07 10:35:42

@Joe.M 

It doesn't seem to be using 4G+, since there is only 1 band listed.

This is how it looks like with 4G+:

 

Recommended Solution
  1  
  1  
#3
Options
Re:MR600 how do i know if its connected to 4G+-Solution
2020-09-07 13:01:33 - last edited 2020-09-08 01:35:56

Finally it works. i relocated my router to different room and getting band 3 and 40 here. but out of the box its not choosing 4g+ for my location. i had to upgrade to beta firmware to choose band myself.

 

Here is my solution:

After updating to beta firmware i tried band 40 and 40 which didnt work, then tried band 3 and 40, now i see 4g+ on UI. but when i restart my router its back to only band 40 so no 4g+. so the trick is to keep the router on 24/7 i guess.

and 4g+ dosnt comes back that easy i had to play around with band setting to bring it back. here is the steps

1. choose no band on one and 40 on other and save it,

2 now change no band to band 3 and save. now it connects to both band, and keep the router on. if router restarted it will be back to only one band, so have to redo the steps again. i think its because my house located in outer circle of city. from reviews i see lucky people with 4g tower nearby gets 4g+ out of the box without beta firmware.

 

edit:

i lost band 3 even without restarting the router. looks like im going to need a antenna.

Recommended Solution
  1  
  1  
#6
Options
5 Reply
Re:MR600 how do i know if its connected to 4G+
2020-09-06 16:47:54

speed test result is very poor. just 3mb/s download speed. my phone has better speed 8mb/s, so the router is not connected to 4g+ for sure. from amazon reviews, out of the box 4g+ worked for airtel and Jio, i dont know why its not working for me.

  0  
  0  
#2
Options
Re:MR600 how do i know if its connected to 4G+-Solution
2020-09-07 00:27:49 - last edited 2020-09-07 10:35:42

@Joe.M 

It doesn't seem to be using 4G+, since there is only 1 band listed.

This is how it looks like with 4G+:

 

Recommended Solution
  1  
  1  
#3
Options
Re:MR600 how do i know if its connected to 4G+
2020-09-07 10:32:31

@Joe.M Yes, you are rightyes

And @Joe.M maybe you could try to use the beta firmware to manually choose two bands for MR600;

Thank you！

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options
Re:MR600 how do i know if its connected to 4G+
2020-09-07 10:36:51 - last edited 2020-09-07 10:40:37

@Joe.M 

   Airtel Band 1 and Band 8 is horrible,

Band 40 is good, I get atleat 15Mbps, with 40+40 it's about 25Mbps, the tower is about 2.5 KM from my house. (I am NOT on BETA firmware)

If we get Band3+Band40 that would be the best i think, I have seen on my mobile band 3 and band 40 go beyond 50Mbps at atmost 2KM from the tower.

  0  
  0  
#5
Options
Re:MR600 how do i know if its connected to 4G+-Solution
2020-09-07 13:01:33 - last edited 2020-09-08 01:35:56

Finally it works. i relocated my router to different room and getting band 3 and 40 here. but out of the box its not choosing 4g+ for my location. i had to upgrade to beta firmware to choose band myself.

 

Here is my solution:

After updating to beta firmware i tried band 40 and 40 which didnt work, then tried band 3 and 40, now i see 4g+ on UI. but when i restart my router its back to only band 40 so no 4g+. so the trick is to keep the router on 24/7 i guess.

and 4g+ dosnt comes back that easy i had to play around with band setting to bring it back. here is the steps

1. choose no band on one and 40 on other and save it,

2 now change no band to band 3 and save. now it connects to both band, and keep the router on. if router restarted it will be back to only one band, so have to redo the steps again. i think its because my house located in outer circle of city. from reviews i see lucky people with 4g tower nearby gets 4g+ out of the box without beta firmware.

 

edit:

i lost band 3 even without restarting the router. looks like im going to need a antenna.

Recommended Solution
  1  
  1  
#6
Options

Information

Helpful: 0

Views: 1524

Replies: 5

Related Articles
MR600 4G+ is not working
2529 7
MR600 v3 4g/4g+ issue
1295 0
Archer MR600 4G BANDS
29064 6
4G MR600 Modem and similar
631 0
Archer MR600 - 4G Bands selection
25816 11
MR600 - not compatible with Three UK 4G+
23188 2
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.