Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Deco M4, cant setup DDNS

< Deco

Deco M4, cant setup DDNS

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco M4, cant setup DDNS

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco M4, cant setup DDNS

2020-07-09 15:39:51 - last edited 2020-07-30 08:38:41

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-07-09

Deco M4, cant setup DDNS

2020-07-09 15:39:51 - last edited 2020-07-30 08:38:41

Model: Deco M4

Hardware Version:

Firmware Version: 1.1.8

Hello

I have problem with setup DDNS on my M4.

I have router from my ISP, and Deco conected to him, so my Deco dont have public IP.

Deco have adres 192.168.8.xxx and devices conected to Deco 192.168.68.xxx

I turn on DDNS in deco app, but its not work, i cant reach my devices from xxxxx.tplinkdns.com:xxxx (ofc i forwarded ports too)

i asume that i have to doing somethink on my first router (from my ISP), but idk what...,

can some1 help me, pls :)

ty in advance

0

0

#1

1 Accepted Solution

2020-07-30 08:38:16 - last edited 2020-07-30 08:38:41

Posts: 12776

Helpful: 1790

Solutions: 1294

Stories: 9

Registered: 2020-04-14

Re:Deco M4, cant setup DDNS-Solution

2020-07-30 08:38:16 - last edited 2020-07-30 08:38:41

Hello, sorry to respond late.

You are correct, you need to do port forwarding on your front-end router for the Deco as well, may I know the model of it? It is suggested to contact the modem/router support to get some suggestions.

Or you may try to change the front-end modem/router into bridge mode and dial up on the main Deco directly, which may allow you to get a public IP address on the main Deco and there will be no need to do port forwarding on that bridge modem anymore.

May this helps.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Recommended Solution

0

0

#2

1 Reply

2020-07-30 08:38:16 - last edited 2020-07-30 08:38:41

Posts: 12776

Helpful: 1790

Solutions: 1294

Stories: 9

Registered: 2020-04-14

Re:Deco M4, cant setup DDNS-Solution

2020-07-30 08:38:16 - last edited 2020-07-30 08:38:41

Hello, sorry to respond late.

You are correct, you need to do port forwarding on your front-end router for the Deco as well, may I know the model of it? It is suggested to contact the modem/router support to get some suggestions.

Or you may try to change the front-end modem/router into bridge mode and dial up on the main Deco directly, which may allow you to get a public IP address on the main Deco and there will be no need to do port forwarding on that bridge modem anymore.

May this helps.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Recommended Solution

0

0

#2