Home Network Community > Deco > Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network
< Deco

Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network
Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network
2020-04-24 13:56:51
Model: Deco M5  
Hardware Version: V3
Firmware Version: 1.4.4 Build 20200221 Rel.65392

Please help,

 

I purchased the DECO M5 three pack and connected as instructed and all works fine with exception to my two NAS drives (D-Link 323 and WDCloud) these will not see the network.

 

I have trnned off the wifi from the Virgin Hub but haven't put it into Modem Mode

 

The Deco M5 Operator Mode is on default Router Mode not Access Point

 

Before I box it all up and send it back as incompatible I hope that someone could point me in the right direction?

 

Diagram Attached

 

Many thanks in advance.

File:
Virgin Hub 3 to Deco M5.pngDownload
  0      
 
  0      
 
#1
Options
3 Reply
Re: Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network
2020-04-29 07:25:51

anyone?

  0  
  0  
#2
Options
Re: Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network
2020-05-16 06:36:04

@Videoatari 

In your network diagram, what's the IP address of the two NAS drives?
When you connect a laptop to the Deco's Wi-Fi, can you ping the IP address of the NAS drive successfully?

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#3
Options
Re: Virgin Superhub 3.0 to Deco M5 - Cannot Get My NAS Drives to see the Network
2020-07-16 23:44:18
Did you get anywhere with this. I have the same problem. Can't see my WDMyCloud NAS drive. I switched off wireless on my ISP's router, leaving it to the Deco's, and my NAS dissapeared. I've now put the Deco into Access Point mode and the NAS has reappeared, but I'm not sure if I need the features of the Deco that are turned off when you switch to AP mode.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 2429

Replies: 3

Related Articles
Cannot find my QNAP Nas after setup of Deco M5
1762 0
Deco M5 cannot find NAS after firmware update
6948 0
 M5 set up with Virgin Superhub 3 in the UK
2942 0
 virgin superhub
1008 0
Deco M9 and Virgin Superhub3
856 0
 First Day - Cannot connect - Virgin Super Hub 3
472 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.