Home Network Community > 5G/4G Wi-Fi Routers/MiFi > Archer MR200 v4 bridge mode
< 5G/4G Wi-Fi Routers/MiFi

Archer MR200 v4 bridge mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer MR200 v4 bridge mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer MR200 v4 bridge mode
Archer MR200 v4 bridge mode
2019-12-10 08:45:12 - last edited 2019-12-10 12:16:17
Model: Archer MR200  
Hardware Version: V4
Firmware Version:

Morning

 

I've just setup a linksys velop with 3 nodes to my MR200 v4

 

Everything seems to be working but there was a couple of drop outs. I think it could be to do with the MR200 still broadcasting WiFi and confusing the velop nodes.

 

I have looked online and there should be a WDS button on the tplinkwifi.net interface but I think this could be from an earlier version of firmware. 

 

Can someone please help me with getting my v4 into bridge mode? Is it even possible? Will be disappointed if not 😥

 

Thanks in advance

 

Tom

  1      
 
  1      
 
#1
Options
6 Reply
Re:Archer MR200 v4 bridge mode
2019-12-10 12:16:07 - last edited 2019-12-10 12:16:17

@Tommys90 

 

What do you mean by saying bridge mode of Archer MR200? Do you want to connect it to the main router by wireless boost the wifi signal or it works as the bridge to work with the SIM card to provide internet? 

 

What is the current network diagram also? Please provide more details.

 

Please follow the instruction below to login: https://www.tp-link.com/support/faq/1656/

Note: tplinkwifi.net is for wireless router, while not applies to Archer MR200. 

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#2
Options
Re:Archer MR200 v4 bridge mode
2019-12-10 13:17:28

@Kevin_Z 

 

Hi Kevin, thanks for the response. 

 

I want the MR200 to basically receive the 4G signal only. 

 

I have a node connected to it by cable which then distributes the WiFi signal around the house. 

 

So effectively, I just want it to be a pass through to the Linksys Velop nodes. 

 

I'll post up the network diagram later - just at work at the moment so I can't login to the router. 

 

Thanks 

 

Tom

  0  
  0  
#3
Options
Re:Archer MR200 v4 bridge mode
2019-12-10 19:07:34

@Kevin_Z 

  0  
  0  
#4
Options
Re:Archer MR200 v4 bridge mode
2019-12-10 19:09:15

@Kevin_Z 

 

I have uploaded network diagram... I got home from work and turned off the WiFi at the back of the router... 

  0  
  0  
#5
Options
Re:Archer MR200 v4 bridge mode
2019-12-11 01:28:02

@Tommys90 

 

Thanks for your reply, so you want to use the MR200 as the internet source with another device works as main router. 

 

The most somple way is that you can disable the wifi function of the MR200 and use the velop to provide internet connection. Like you did earlier. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options
Re:Archer MR200 v4 bridge mode
2020-01-23 07:56:31

@Kevin_Z 

 

I found this thread while searching on how to use my TP-Link TD-W8961N V3 as a wireless extender with my Archer MR200 V4. I do not want to use a LAN cable to connect the devices. Is this possible?

 

The MR200 Emulator on the TP-Link website clearly shows the option of the WDS feature as shown below...

 

 

 

...while my router does not show this option at all, as shown below.

 

 

 

Your advice will be greatly appreciated.

 

Kind Regards

  0  
  0  
#10
Options

Information

Helpful: 1

Views: 12264

Replies: 6

Related Articles
[Archer MR200 v4] Problem with seeing received SMS
7999 3
 Archer MR200 Bridge mode
10002 0
Why Archer MR200 v4 doesn't have WDS(Wireless Distribution System) ?
3057 0
Archer MR200 V4 without internet connection (DCHP problem)
2007 0
 Archer MR200 V4 - External Antennas ?
3948 0
 Archer MR200(EU) V4 - MAC Address Clone
959 4
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.