Home Network Community > Powerline Adapters > PA9020KIT wont enter power saving mode
< Powerline Adapters

PA9020KIT wont enter power saving mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

PA9020KIT wont enter power saving mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
PA9020KIT wont enter power saving mode
PA9020KIT wont enter power saving mode
2019-10-23 17:44:27
Model: Adapter  
Hardware Version: V1
Firmware Version: 3.2.4_902011_170703_903

The device wont enter power saving mode.

 

Thia is supposed to be signified by a flashing green power button (3secs)....after 5 mins of power down of connected device

 

My TP devices power buttons stay permanant green after connected device is switched off

 

Chris.... smiley

  0      
 
  0      
 
#1
Options
3 Reply
Re:PA9020KIT wont enter power saving mode
2019-10-24 03:50:55

@chrismckay 

 

You can follow the instruction attached below to setup the power saving mode. 

https://www.tp-link.com/support/faq/2018/

 

Note: You need do that with the tpPLC utility together. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:PA9020KIT wont enter power saving mode
2019-10-24 05:40:49

@chrismckay 

 

Turns out that one network adapter being connected to my router is permanently on because the router never switches off. The second network adapter is fitted to an amazon firestick via a crossover adapter which has its own power supply independant of my television so infact it is never powered off, so in both cases the network adapters cannot switch to power saving mode because it has a demand on it.

 

This was proven by switching off the firestick power at the wall socket, the network adapter resorted to power saving after 5 minutes

 

Chris...smiley

  0  
  0  
#3
Options
Re:PA9020KIT wont enter power saving mode
2019-10-25 07:41:35

@chrismckay 

 

Thanks for your explanation; cause the appliance are running all the time, the powerline adapter cannot switch to power saving mode. 

 

You can turn off the firestick power to restore the power saving mode as workaround for now.

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 960

Replies: 3

Related Articles
 Power saving mode
466 0
 My TL-PA8015P KIT is stuck in power saving mode
700 0
TL-PA8010PKIT - any way to turn off Power Saving Mode?
2844 0
 PA4030 does not go into power-saving mode!
571 0
  power saving
414 0
 TL-PA8010P Kit Power-saving Mode not working?
1021 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.