Archer MR400 disconnect from internet
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Router used with 4G sim card disconnects from internet after running for a few hours. Restart needed to get internet working again. Full 4G signal where used. Any ideas what to do to fix this issue?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
As you can see the signal quality is not an issue. You can set 4G only without any problem.
I would suggest you following two steps:
- swap the sim card in your mobile phone to check how your mobile is working with the sim from MR400..
- if confirmed sim card is okay than restore factory settings and start again using default settings for plug & play of sim card.
In a picture you posted above a traffic of 1.2 GB is recorded which means the modem was working. Perhaps a wrong setting was done, this is why you should try to restore factory settings, remove the sim and start again the device like a new one. To restore factory settings: Advanced - System Tools - Backup & Restore - Factory Restore.
Once you have confirmation that sim card is okay and after factory restore still same problem than is a HW issue either service repair or replacement of device.
- Copy Link
- Report Inappropriate Content
Hi, any news on how to solve this issue? Still having the same problem...
- Copy Link
- Report Inappropriate Content
Hello, there is a new released which you can install and verify its performance;
If it still does not work, we will get some logs to do further analysis and try to fix it.
Our engineer will email you the download link and information we need, please check your inbox.
Good day.
- Copy Link
- Report Inappropriate Content
I am having the exact same problems with the exact same symtoms. I constantly run Speedtests on my home network since I switched to a Three SIM for data instead of expensive fibre internet.
I have also fitted an external aerial to my house and get a very good signal from this now - download speeds increased by at least 20MBPS compared to the fibre connection.
So when it works, it is good.
But as of about a month ago, the internet drops out and I have to reboot the MR400 router every 2 to 3 days, but this is required now pretty much every day. I have even set the MR400 to reboot every day at 06:00 in the settings.
The internet drops out for what seems like a a minute or so and then reconnects. The lights on the MR400 still show the wireless, Internet and power symbols. The signal; strenghts is mostly at 100%, but sometimes drops to 75% for a few minutes.
I have set the channel width to 20MHz and left the channel selection to Auto as recommended.
The debug tool link no longer works by the way.
Very frustrating.
I will try another SIM - from my mobile phone (also Three) to see if it is the SIM perhaps
Edit: second SIM did not improve things.
My current MR400 device info:
Device Information
Firmware Version: 1.12.0 0.9.1 v0001.0 Build 190730 RC.59984n
Hardware Version: Archer MR400 v3 00000001
@Kevin_Z Do you have a Beta version for the MR400 for us to test like you did with the MR6400 perhaps?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
To those who may be concerned,
Hi all, if you have the disconnection issue with your LTE gateway, please help us to provide the information attached below. So that we can speed up the whole process and locate your issue quickly and try to figure it out.
1. The model number of your LTE gateway router. And its hardware and firmware version.
Note: Please ensure the firmware is up to date.
2. Please give us a brief introduction of the disconnection issue and the troubleshooting method you have done and the corresponding results.
Note: Like the LED status, whether both wifi/wired connection do not work or just one of them, how often it stops working, whether the sim card works well in cellphone directly, whether the router still has a valid IP address and gateway when it stops working.
3. You can test whether the sim card works well with your cellphone, or you can change another SIM card to check the stability; create the network profile manually/change wifi settings are worth giving it a go as well.
https://www.tp-link.com/support/faq/1663/
4. When your router stops working, you can take some screenshots, including the Basic-network map page, the advanced-status page, the advanced-network-internet page. They will help us to do further analysis.
Thanks for your support and cooperation in advance. Good day.
- Copy Link
- Report Inappropriate Content
The requested data is sent in an email to support.se@tp-link.com.
I also noted that the router is listening to a number ports which can not be disabled in the user interface:
| Port 22 (TCP) |
Dropbear sshd 2017.75 protocol 2.0 |
| Port 23 (TCP) |
BusyBox telnetd 1.14.0 or later |
| Port 53 (TCP) |
domain |
| Port 80 (TCP) |
|
| Port 1900 (TCP) |
Portable SDK for UPnP devices 1.6.19 Linux 2.6.36; UPnP 1.0 |
| Port 7547 (TCP) |
TP-LINK TR-069 remote access |
I have blocked outside access to these ports in my firewall. Maybe this issue should be placed in a separate topic....
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@MaWi
Very same problem, engineer said it was faulty device but TP-link is refusing to replace a 3 month old router because i don't have recipe anymore.
It woul seem i am not only one having this exact same issue and yet they don't have fix for it. I suspect its either fault hardware or fault software based on the fact they are trying make everyone support go private which means they are tying to hid something.,
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 3
Views: 22822
Replies: 67
Voters 1
