Home Network Community > Wi-Fi Routers > Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
< Wi-Fi Routers

Solution Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Solution Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
SolutionArcher C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-01-05 10:02:55 - last edited 10 hours ago
Tags: #Guest Network #Access Point Mode #Official

Update on Nov 19th, 2024:

This issue discussed here in the thread has been resolved with official releases. If anyone encounters a similar problem, please ensure you're running the latest official firmware on your TP-Link device.

 

We also provide a newer and pre-release version of firmware in the following thread to introduce a host of new features and optimizations, it's suggested to upgrade and install the pre-release version to explore more new features:

Pre-release Firmware for Archer C80/A8/C6/C86 Brings a Host of New Features and Optimizations

 

-------------------------------------------------------------------------------------------------------------------------------------------------------------------

This Article Applies to:

Model: Archer A6v4, Archer A64v1, Archer A8v1&v2.2, Archer C59v4, Archer C6v4, Archer C64v1, Archer C80v1&v2.2

Firmware:  1.13.2 Build 230824

 

Phenomenon Description:

Following the firmware update to the latest version 1.13.2 Build 230824, some customers have reported issues with the guest network in AP mode. Specifically, devices connected to the guest network are unable to access the internet, and the guest network section in the Web UI may display abnormal especially the Guest Permissions part like below:

Workaround:

If you encounter similar issues, we recommend the following two workarounds, please try either one and confirm if the issue can be resolved:

Workaround 1: please try following steps:

1) Switch the device from AP mode to router mode. 

2) Perform a factory reset by holding reset button for about 10s. Please note that all the previous configurations will be lost.

3) After the factory reset, switch the device back to AP mode.

4) Check if the guest network works fine. 

 

Workaround 2. You could also download and update the following beta firmware:

For Archer A64v1, A8v1, C59v4, C64v1, C80v1(They use the same beta): Archer C80_V1_20231229

For Archer A6v4, A8v2.2, C6v4, C80v2.2: try this beta firmware

 

Note: Please be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding.

 

If there is still any problem after trying the two workarounds, please leave your comments with model no., hardware version, firmware version of your TP-Link device, its working mode, and detailed problem description.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  4      
 
  4      
 
#1
Options
16 Reply
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-01-21 23:22:43

  @Sunshine i cannot access my wifi device

  1  
  1  
#8
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-01-23 01:56:12

  @Eliassalim 

 

Hi, please provide more details about the issue, do you mean you are unable to connect the WiFi? any error message?

And what is the model no., hardware version and LED status of the device?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#9
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-01-25 05:05:54 - last edited 2024-01-25 05:18:05

@Sunshine 

 

A suggestion regarding release notes of FW releases since many users have turned off auto update feature (or it has not been implemented at all) on their devices - they are cautious regarding new FW releases.

For example:

 

Archer C64(EU)_V1_1.13.2 Build 230824

Published Date: 2023-09-08 Language: Multi-language File Size: 3.80 MB

Modifications:
1.Added support for DoH.
2.Added support for Alexa
3.Added support for HTTPS access.
4.Added IoT network and IoT security.
5.Optimized the guest network, supports Access Time Control and Bandwidth Control.
6.Optimized the easymesh, supports upgrading multiple devices at the same time.
7.Optimized the UI.

Bug Fixed:
1.Fixed several bugs related to IPTV.
2.Fixed several UI bugs.
3.Fixed the bug that the pin doesn't work under certain scenarios.
4.Fixed a compatibility bug with certain intel network cards.
5.Fixed the bug that router can't be accessed remotely via tether.

Note: You will be unable to downgrade to the previous firmware version after updating this firmware.

Known Issues:

1. Guest Network in AP Mode Stops Working

 

Adding a new section "Known Issues" would be very informative for a user who has to decide whether to upgrade or not to this FW release, since he can't revert back to the previous one.

In this case:

if the user is not using the device in AP mode he can proceed with the FW update.

If the user will use the device in AP mode he would know for the possible issue and won't proceed until issuing a beta or next stable FW release.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  1  
  1  
#10
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-01-25 09:41:10

  @terziyski 

 

Thank you for your valuable suggestion!

Typically, issues are reported and identified after a firmware release. This means that there are usually no known issues at the time of releasing the firmware and creating the release note. However, if any serious problems are identified, maybe we could consider updating the release note. We will forward your suggestion to our senior engineer for evaluation.

We appreciate your continuous support and the warm-hearted help you provide to other users. Thank you!

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#11
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-01-25 18:34:35

  @Sunshine 

 

Yes, that's what I've meant - when the problem is identified to update the FW release notes.

Thus an unneccessary overhead for users and your team would be spared.

This would also improve the overall user experience and company image.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  1  
  1  
#12
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-02-23 07:46:26 - last edited 10 hours ago

Hi All,
 

Please note that there is a new beta firmware for Archer C80 V2.2,  Archer C6 V4, Archer A8 V2.2, Archer C86 V1 with L2TP over IPSec VPN Server function, which also resolved this random restarting issue, it is recommended to try the new beta firmware and experience the L2TP over IPSec VPN Server function:

Public Beta Firmware for Archer C80 V2.2/C6 V4/A8 V2.2/C86 V1 Supports L2TP over IPSec VPN Server 

 

Remember to leave us your comment whether the new beta firmware works fine.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  2  
  2  
#13
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-02-23 19:15:11

  @Sunshine i can't test VPN but please fix the timezone option where always reset to a internet check after i changed to managed by connected device

  0  
  0  
#14
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-02-26 01:46:20

  @itachimetal 

 

Hi, could you please provide more details about the timezone issue? and does the issue start to happen after updating to the new beta firmware?

If you have updated to the new beta firmware, it is recommended to leave your comment on this thread even though you are not testing VPN: Public Beta Firmware for Archer C80 V2.2/C6 V4/A8 V2.2/C86 V1 Supports L2TP over IPSec VPN Server

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#15
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-03-22 11:30:49 - last edited 2024-03-22 11:33:53

  @Sunshine Hi, I am currently using the beta firmware for the Archer C64 1.0 (Beta Firmware Version 1.13.5 Build 231228 Rel.63705n(4555)) linked on this thread, and I noticed that DNS over HTTPS (DoH) isn't working on my router. Once enabled, the status is stuck on "Connecting..." and does not progress further.

 

I tested with Quad9 and Cloudflare DNS, and by using their respective testing instructions, I was able to verify that DoH isn't being used for either provider.

 

The DoH feature works on the latest public version (Firmware Version 1.13.2 Build 230824 Rel.74702n(4555)). Unfortunately, I had to move off of that version since I am experiencing intermittent Internet connectivity dropouts after around 20-30 minutes from the router being turned on. (Internet connection is lost on all devices connected to the router, including wired devices. The router is used in Router (not AP) mode, and the Guest Network feature is not being used.)

 

However, the beta firmware linked on this forum thread has no such issue, and after continuously running it for 24 hours non-stop, no such dropouts occurred. I'll be staying on the beta firmware version for the meantime.

 

With that, I would like to know if the DoH issue can be resolved. Thanks!

(Edited for clarification, fixed formatting, removed links, and indicated hardware version)

  1  
  1  
#16
Options
Re:Archer C80/C64v1/C6v4 Guest Network in AP Mode Stopped Working after Updating 1.13.2 Build 230824
2024-03-25 03:17:18

  @rosscercado 

 

Thank you very much for the feedback, I've sent you a private message, please have a check and let us know if it helps.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#17
Options
12

Information

Helpful: 4

Views: 2595

Replies: 16

Tags

Guest Network Access Point Mode Official
Related Articles
Archer C80v1&v2.2/C64v1/C6v4 Restarting Randomly
3244 5
Archer C80. Should I use it in router mode or AP mode?
747 0
Archer AXE75 guest network ?
741 0
 Disconnections on Archer C80 in AP mode
543 1
 Archer C64 guest network in AP mode has access to LAN
927 0
Guest Network Bandwidth Control of Archer C80
1330 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.