Home Network Community > All Threads > Deco wifi clients
< All Threads

Deco wifi clients

Deco wifi clients

Deco wifi clients
Deco wifi clients
Sunday
Tags: #Network Connectivity
Model: Deco X50-5G  
Hardware Version: V1
Firmware Version: 1.2.1

Hi guys.

I'm looking for some help with a new Deco X50-5G (v1 1.2.1) upgrade from an Archer MR200 4g. I have three M9-Plus satellite units connected by ethernet and many Kasa and Tapo devices.

I believe the ISP is good. It's the same 4g sim, I'm waiting for the 5g account upgrade. Speed tests are good.

The system which was rock solid is now suffering many connection issues. My Android galaxy S23 will not stay connected to the WiFi. It seems also the problem with the Tapo devices which show disconnected in the Tapo app.

It also failed with the red LED. I could not access it and reset it.

Could it be an issue with the ip address reservation? The M9-Plus units also show green, solid red and flashing red.

Can the X50-5G be used for ISP connection and a main M9-Plus to provide ip addresses?

Many thanks.

  2      
 
  2      
 
#1
Options
2 Reply
Re:Deco wifi clients
Monday

  @tap0 

Hi, Since the SIM card uses 4G network, have you tried to set the "Network Mode" on the Deco X50-5G to "4G only"?

 

I don't think IP address reservation might cause the instability issue.

 

Can the X50-5G be used for ISP connection and a main M9-Plus to provide ip addresses?

- Deco X50-5G supports "Bridge Mode" under Deco APP>More>Operation Mode. You could set it in "Bridge mode" and then create a new Deco Mesh via Deco M9 plus. Deco M9 plus will work as the DHCP router.

Thank you very much and best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:Deco wifi clients
18 hours ago

  @David-TP 

 

I might have solved the problem. After many attempts to log in to the web management page, it showed an M9-Plus satellite as the main Deco. This wasn't shown in the app. I disconnected the ethernet to that M9-Plus and the system appears stable.

 

Thanks.

David-TP wrote

  @tap0 

Hi, Since the SIM card uses 4G network, have you tried to set the "Network Mode" on the Deco X50-5G to "4G only"?

 

I don't think IP address reservation might cause the instability issue.

 

Can the X50-5G be used for ISP connection and a main M9-Plus to provide ip addresses?

- Deco X50-5G supports "Bridge Mode" under Deco APP>More>Operation Mode. You could set it in "Bridge mode" and then create a new Deco Mesh via Deco M9 plus. Deco M9 plus will work as the DHCP router.

Thank you very much and best regards.

 

  0  
  0  
#3
Options

Information

Helpful: 2

Views: 53

Replies: 2

Tags

Network Connectivity
Related Articles
Deco packets loss between internet and WiFi clients, not cabled clients
212 0
Deco M4 wifi clients with wifi connected and "no internet"
39086 2
Deco X50-5G and EE (UK) SIM
1044 0
Deco X50-5G ja Samsung A twenty-five (Androin)
88 1
Deco not picking up clients
654 0
Deco X50-5G tethering through mobile phone
219 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.