Home Network Community > All Threads > 10 MBPS Half Duplex at Wan Input Port
< All Threads

10 MBPS Half Duplex at Wan Input Port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

10 MBPS Half Duplex at Wan Input Port

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
10 MBPS Half Duplex at Wan Input Port
10 MBPS Half Duplex at Wan Input Port
2023-12-03 08:29:35 - last edited 2023-12-06 06:34:24
Model: TL-WR845N  
Hardware Version: V4
Firmware Version: 0.9.1 3.17 v0001.0 Build 201214 Rel.67500n

Connection Topology - OFC Cable to GPON Modem to TP link router

 

My Router is dropping speed and the maximum I am getting is at 7-8 MBPS.
My connection though is at 50 MBPS
 

Checked it with Cable directly from GPON Modem and its at 50MBPS
Checked it wirelessly through router at was between 7-8 MBPS
Checked it wired from router it was at 7-8 MBPS

 

Also checked if the cable was at fault by changing the cable.

 

Noticed that WAN input shows 10MBPS Half Duplex.

 

Can someone suggest a solution?

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:10 MBPS Half Duplex at Wan Input Port-Solution
2023-12-05 15:57:31 - last edited 2023-12-06 06:34:24

  @Sunshine 

 

Thanks for responding
 
Yes I was able to see Full duplex with same cable when directly connected to the ISP but same showed half duplex via router to PC.


Surprisingly the router now shows Full duplex automatically without me doing anything.
Can you please suggest is my firmware version is update with respect to the HW version
below mentioned is my current status and if i need to do anything.

I am worried this issue should not occur again.
 

Status

Firmware Version:0.9.1 3.17 v0001.0 Build 201214 Rel.67500n

Hardware Version:TL-WR845N v4 00000004

 

Ethernet

 

Internet:100Mbps full duplex

LAN1:Unplugged

LAN2:Unplugged

LAN3:Unplugged

LAN4:Unplugged

 

Recommended Solution
  0  
  0  
#3
Options
7 Reply
Re:10 MBPS Half Duplex at Wan Input Port
2023-12-04 07:55:26 - last edited 2023-12-04 07:56:08

  @Sanket-11 

 

May I have a screenshot of the router WAN port negotiation speed and duplex mode? 

And are you able to check the duplex mode as well when connecting a computer directly to the ISP modem with the same cable?

 

Please try resetting the router to factory defaults by holding reset button for about 10s to see if it helps.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  1  
  1  
#2
Options
Re:10 MBPS Half Duplex at Wan Input Port-Solution
2023-12-05 15:57:31 - last edited 2023-12-06 06:34:24

  @Sunshine 

 

Thanks for responding
 
Yes I was able to see Full duplex with same cable when directly connected to the ISP but same showed half duplex via router to PC.


Surprisingly the router now shows Full duplex automatically without me doing anything.
Can you please suggest is my firmware version is update with respect to the HW version
below mentioned is my current status and if i need to do anything.

I am worried this issue should not occur again.
 

Status

Firmware Version:0.9.1 3.17 v0001.0 Build 201214 Rel.67500n

Hardware Version:TL-WR845N v4 00000004

 

Ethernet

 

Internet:100Mbps full duplex

LAN1:Unplugged

LAN2:Unplugged

LAN3:Unplugged

LAN4:Unplugged

 

Recommended Solution
  0  
  0  
#3
Options
Re:10 MBPS Half Duplex at Wan Input Port
2023-12-06 06:34:21

  @Sanket-11 

 

Glad to hear that it has been working fine on its own.

 

In addition, there is a newer firmware than yours, so you could also download the latest firmware from our official website and update it manually:

Firmware Download for TL-WR845N V4

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options
Re:10 MBPS Half Duplex at Wan Input Port
2023-12-07 17:14:12

  @Sunshine 

The issue is back again

You can check the screenshot below.

Speed dropped to 8MBPS

Screenshot

  0  
  0  
#5
Options
Re:10 MBPS Half Duplex at Wan Input Port
2023-12-08 01:41:59

  @Sanket-11 

 

Could you please download the latest firmware from our official website and update it manually to see if it solves the please completely?

Firmware Download for TL-WR845N V4

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#6
Options
Re:10 MBPS Half Duplex at Wan Input Port
2023-12-08 05:08:12

  @Sunshine 

Now my router is updated with the newest firmware for it.

On update and reboot, the router was on 100MBPS full duplex but after a while went back to 10MBPS half duplex.
can we identify what the actual problem is?

 

Is the Hardware at fault?

i need to solve this issue ASAP. My work is being hampered.

find below screenshot after update.

 

Status

 

Firmware Version:0.9.1 3.19 v0001.0 Build 221027 Rel.59106n

Hardware Version:TL-WR845N v4 00000004

 

LAN

MAC Address:40:ED:00:EE:77:BA

IP Address:192.168.0.1

Subnet Mask:255.255.255.0

 

Wireless 2.4GHz

Operation Mode:Router

Wireless Radio:Enabled

Name(SSID):Godiyal 2-GHz

Mode:11bgn mixed

Channel:Auto(Channel 4)

Channel Width:Auto

MAC Address:40:ED:00:EE:77:BA

 

 

WAN

MAC Address:40:ED:00:EE:77:BB

IP Address:100.106.18.207(PPPoE)

Subnet Mask:255.255.255.255

Default Gateway:10.0.0.1

DNS Server:111.125.211.252 111.125.211.250

Online Time:0 day(s) 06:33:10

 

 

Ethernet

Internet:10Mbps half duplex

LAN1:Unplugged

LAN2:Unplugged

LAN3:Unplugged

LAN4:Unplugged

 

 

System Up Time:0 day(s) 06:33:37

 

 

 

 

  0  
  0  
#7
Options
Re:10 MBPS Half Duplex at Wan Input Port
2023-12-08 06:46:58

  @Sanket-11 

 

Hi, 

 

You mentioned "Checked it with Cable directly from GPON Modem and its at 50MBPS“ in your original post, please try testing the GPON Modem again and monitor for longer time since the issue happens after a while on the router.

 

If the GPON Modem is always working on 100Mbps full duplex with your computer with the same cable, it might be either the WAN port issue of the router or some compatibility issue between the GPON Modem and the router.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#8
Options

Information

Helpful: 1

Views: 1220

Replies: 7

Related Articles
Sometimes my WAN going to 10 mbps Half Duplex
1317 5
Power line Full or Half Duplex
2743 0
Network speed capped at 10mbps half-duplex
209 0
Archer C80 WAN port shuts down on 1000 Mbps
1038 1
lan port ax 73 after pppoe down to 10mbps half duplex
558 1
Wan port capped at 100 mbps
294 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.