Home Network Community > All Threads > TL-PA4010P Stopped working, seem to be resetting constantly.
< All Threads

TL-PA4010P Stopped working, seem to be resetting constantly.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-PA4010P Stopped working, seem to be resetting constantly.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-PA4010P Stopped working, seem to be resetting constantly.
TL-PA4010P Stopped working, seem to be resetting constantly.
2023-10-05 11:49:02 - last edited 2023-10-05 14:56:51
Model: TL-PA4010P KIT  
Hardware Version: V2
Firmware Version:

After years of faultless service the powerlines stopped talking today.

The following has started happening to both units on the same day. 
Every four seconds the leds go out. Then all light up, go out, then just the ones that should be on i.e. power and connected network light up. Then four seconds later the cycle starts again. 

Tried pressing pair button for 10 seconds. Tried plugging in next to each other. Tried leaving them unplugged for several hours. 
Are they dead?

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:TL-PA4010P Stopped working, seem to be resetting constantly. -Solution
2023-10-05 14:56:42 - last edited 2023-10-05 14:56:51
Problem solved. Accessed them with the Utility program. As soon as I did the cyclical flashing stopped. Reset them for good measure and everything is back working. Really hope it was just a bad day for them. Like the new utility program. A lot easier to follow than the old one. Cheers
Recommended Solution
  0  
  0  
#2
Options
2 Reply
Re:TL-PA4010P Stopped working, seem to be resetting constantly. -Solution
2023-10-05 14:56:42 - last edited 2023-10-05 14:56:51
Problem solved. Accessed them with the Utility program. As soon as I did the cyclical flashing stopped. Reset them for good measure and everything is back working. Really hope it was just a bad day for them. Like the new utility program. A lot easier to follow than the old one. Cheers
Recommended Solution
  0  
  0  
#2
Options
Re:TL-PA4010P Stopped working, seem to be resetting constantly.
2023-10-10 08:10:44

  @Shellington 

 

Hi, thanks a lot for the update, glad to hear that you have solved the problem.

Hope you could enjoy the internet.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#3
Options

Information

Helpful: 0

Views: 541

Replies: 2

Related Articles
TL-PA4010P KIT with TL-WPA4220 KIT
2810 0
TL-PA4010P V5 - How to Update firmware?
103 0
TL-PA4010P KIT
1244 0
TL-PA4010P KIT
848 0
Combine TL-PA4010P with TL-WPA4220
687 0
Is it safe to plug in ps5 to the socket on the back of the TL-PA4010P KIT
560 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.