Home Network Community > All Threads > X50 issues in AP mode
< All Threads

X50 issues in AP mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

X50 issues in AP mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
X50 issues in AP mode
X50 issues in AP mode
2023-06-11 11:32:52
Tags: #Access Point Mode
Model: Deco X50   Archer AX3000  
Hardware Version:
Firmware Version:

Hello,

 

I have issues with functionality of DECO X50 system when used in Access Point mode

 

I have TP-Link Archer AX3000 as a router connected to cable modem

2x X50s are connected to LAN ports of AX3000 as below:

 

With this configuration X50s are going offline each 3-5minutes an fail to serve their purpose

I cannot interconnect X50s directly due to pre-installed UTP cabling in the apartment

 

Both LAN ports on the router work fine, tested on PC

 

What am I missing?

 

Thanks

BR
Dima

  2      
 
  2      
 
#1
Options
3 Reply
Re:X50 issues in AP mode
2023-06-12 11:42:47

  @DolotinD 

Hi, would the Deco X50 turn red during the disconnection?

Do you need to restart Deco to get the internet back or would it reconnect automatically?

If only the main Deco X50 is connected to AX3000, the satellite X50 is temporarily unplugged or wirelessly connected to the main X50, would the disconnection repeat again?

Wait for your reply.

Best regards.

 

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:X50 issues in AP mode
2023-06-13 09:03:51
Hi David, 1. During the outage, DECOs LED turns stable red 2. After some time DECO reconnects automatically for a short time and then the issue repeats again 3. If only one of the DECOs is backhauled by GE from AX3000 and the 2nd one is backhauled by 2.4/5GHz from the 1st DECO - the network is stable and functions normally. This is however not my preferred layout due to the fact that BH SSID has to penetrate 2 walls and therefore bandwidth shrinks by ~80% Thanks Regards, Dima
  2  
  2  
#3
Options
Re:X50 issues in AP mode
2023-06-13 11:49:28

  @DolotinD Hi, Thanks for getting back to me.

I would like to forward your case to the senior engineers for further assistance. Please check the email for more suggestions.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  1  
  1  
#4
Options

Information

Helpful: 2

Views: 583

Replies: 3

Tags

Access Point Mode
Related Articles
No internet connection in AP Mode with X50
1296 0
Deco X50 LAN Ports in AP Mode
356 0
Deco X50 ap mode wifi slow suddenly
402 0
XE75 - AP Mode Ports
326 0
Deco Mesh (x50) and Omada and Starlink / why frequent issues? AP or router mode
557 0
X50-POE AP MODE Guest network
493 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.