Home Network Community > All Threads > Pinging other devices in AP mode not possible
< All Threads

Pinging other devices in AP mode not possible

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Pinging other devices in AP mode not possible

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Pinging other devices in AP mode not possible
Pinging other devices in AP mode not possible
2023-03-31 06:55:03 - last edited 2023-04-03 13:27:51
Tags: #Access Point Mode
Model: Deco M9 Plus  
Hardware Version:
Firmware Version:

Dear all,

 

I have problem when pinging devices in my network. My network setup as follows:

 

- Router of my internet provider is connected to the internet

- First Deco is connected to this Router

- PC1 is connected with Router (lan cable)

- PC2 is connected with second Deco (lan cable)

Tried pinging PC1 from PC2 -> FAILED

 

After that I switched the Deco to Access Point mode with my mobile app

Tried pinging PC1 from PC2 again -> FAILED

 

I thought access point mode would bridge the Deco and the Router network?!

 

How can I achieve that all my home devices are located in the same network, no matter they are connected to Deco or the Router?

 

Thanks in advance for your help!

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Pinging other devices in AP mode not possible-Solution
2023-03-31 11:20:35 - last edited 2023-04-03 13:27:51

  @Roger_Kaputnik 

 

Deco Operation Mode change in app does not propagate instantly to all your Deco mesh nodes, you may need to give it few minutes.

 

Try this way:

 

1. In Deco app change Operation Mode to Access Point. Close Deco app. Wait for about 3-5 minutes.

2. Open Deco app. Verify it reports Access Point as Operation Mode.

3. Reboot PC1 and reboot PC2. Check in your router that it assigned IP addresses to both PC1 and PC2. Check on both PCs that they have IP addresses from IP range configured in router.

4. If all checks passed, pinging between PCs should work at this point.

Recommended Solution
  1  
  1  
#2
Options
2 Reply
Re:Pinging other devices in AP mode not possible-Solution
2023-03-31 11:20:35 - last edited 2023-04-03 13:27:51

  @Roger_Kaputnik 

 

Deco Operation Mode change in app does not propagate instantly to all your Deco mesh nodes, you may need to give it few minutes.

 

Try this way:

 

1. In Deco app change Operation Mode to Access Point. Close Deco app. Wait for about 3-5 minutes.

2. Open Deco app. Verify it reports Access Point as Operation Mode.

3. Reboot PC1 and reboot PC2. Check in your router that it assigned IP addresses to both PC1 and PC2. Check on both PCs that they have IP addresses from IP range configured in router.

4. If all checks passed, pinging between PCs should work at this point.

Recommended Solution
  1  
  1  
#2
Options
Re:Pinging other devices in AP mode not possible
2023-04-03 13:27:46

Thanks a lot, that worked fine smiley

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 581

Replies: 2

Tags

Access Point Mode
Related Articles
No internet in AP mode
1034 1
Deco M9 plus - is this AP setup possible?
1278 0
Guest wlan to VLAN in AP mode in Deco M9+
16876 51
No wired devices possible on Deco M9 Plus in Router-Mode?
5893 0
Deco M9 Plus in AP mode taking over DHCP server and assigning IPs in own subnet
56231 7
Deco M9+ as AP mode
835 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.