TL-480T+ Wireless Connectivity
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello-
I am planning to purchase TL-480T+ load balancer as I have two internet connections, each reaches max of 30 Mb per second and I want to increase the speed plus balance the load across the family members who needs internet access, specially when all of us are using YouTube at the same time, which seems to be bandwidth killer
So my understanding TL-480T+ doesn't output wireless connection, can I just output the wireless connection by connecting one of its LAN ports to an access point like TL-WA801N ?
Thanks
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hey
Yes that is the device, its just a newer model with faster ports and a bit more power, should do the job for you!\
In answer to you questions..
- My 1st DSL is using TP-Link Archer VR600 OK
- My 2nd DSL is using TP-Link W9960 OK
- I will use Cat6 network cables to connect the above two into ER605 WAN ports Yes recommend CAT6, CAT5e is showing it age now.
- Then I will output 3 Cat6 network cables to connect to TP-Link access points that I will distribute among the house Sounds like a plan
- I believe all the access points will need to have the same name (SSID) for seemless connectivity, I assume the devices should connect to the nearest SSID this way Not exactly.. No. Seamless roaming can only be achieved if a controller is used to "manage" the network and tell the devices to roam, it them handles the move and means you can seamlessly move without disconnecting. If you dont use a controller and just have 3x APs connected with same username/password it wont give you seamless roaming, in fact it likely wont roam. Devices are poor at roaming unless told, they stick to one AP until it dies then disconnect and re-scan for a new one. If you havent bought the APs yet, then you may want to consider managed APs with a controller IF seamless roaming is your thing. Options are something like the OC200 controller and 3x EAP225 / 610s (depending on your needs). If price is a concern, the Deco range may be an option when used in AP mode, but the Omada EAP225 would be better if honest.
- Do I need to do anything for the IPs, I think all the devices will be configured to use DHCP for dynamic IPs. Just make sure the 2x DSL routers have different addresses from your ER605. The ER605 will do the dhcp for all LAN devices, so its likely 192.168.1.1 or something like that. Set your DSL routers to use 192.168.101.x and 192.168.202.x to keep them on seperate networks.
- Copy Link
- Report Inappropriate Content
Hey
Yes you are correct, the router you mentioned does not have WiFi. You are again correct however that connecting an AP to the LAN port would offer you WiFi connections.
However.. just to point out that the TL-480T+ is an older device now, you may be better to consider the ER605 router. Its faster and newer for roughly the same price.
- Copy Link
- Report Inappropriate Content
@Philbert Thanks for the confirmation and the tip, the one you are mentioning is this one Amazon, right?
I believe the 480T+ configuration was very easy, I assume the ER605 configuration is easy as well
For the setup I am planning on the following:
- My 1st DSL is using TP-Link Archer VR600
- My 2nd DSL is using TP-Link W9960
- I will use Cat6 network cables to connect the above two into ER605 WAN ports
- Then I will output 3 Cat6 network cables to connect to TP-Link access points that I will distribute among the house
- I believe all the access points will need to have the same name (SSID) for seemless connectivity, I assume the devices should connect to the nearest SSID this way
- Do I need to do anything for the IPs, I think all the devices will be configured to use DHCP for dynamic IPs
Any comments regarding the setup before I purchase the devices, not cheap in my currency
Philbert wrote
Hey
Yes you are correct, the router you mentioned does not have WiFi. You are again correct however that connecting an AP to the LAN port would offer you WiFi connections.
However.. just to point out that the TL-480T+ is an older device now, you may be better to consider the ER605 router. Its faster and newer for roughly the same price.
- Copy Link
- Report Inappropriate Content
Hey
Yes that is the device, its just a newer model with faster ports and a bit more power, should do the job for you!\
In answer to you questions..
- My 1st DSL is using TP-Link Archer VR600 OK
- My 2nd DSL is using TP-Link W9960 OK
- I will use Cat6 network cables to connect the above two into ER605 WAN ports Yes recommend CAT6, CAT5e is showing it age now.
- Then I will output 3 Cat6 network cables to connect to TP-Link access points that I will distribute among the house Sounds like a plan
- I believe all the access points will need to have the same name (SSID) for seemless connectivity, I assume the devices should connect to the nearest SSID this way Not exactly.. No. Seamless roaming can only be achieved if a controller is used to "manage" the network and tell the devices to roam, it them handles the move and means you can seamlessly move without disconnecting. If you dont use a controller and just have 3x APs connected with same username/password it wont give you seamless roaming, in fact it likely wont roam. Devices are poor at roaming unless told, they stick to one AP until it dies then disconnect and re-scan for a new one. If you havent bought the APs yet, then you may want to consider managed APs with a controller IF seamless roaming is your thing. Options are something like the OC200 controller and 3x EAP225 / 610s (depending on your needs). If price is a concern, the Deco range may be an option when used in AP mode, but the Omada EAP225 would be better if honest.
- Do I need to do anything for the IPs, I think all the devices will be configured to use DHCP for dynamic IPs. Just make sure the 2x DSL routers have different addresses from your ER605. The ER605 will do the dhcp for all LAN devices, so its likely 192.168.1.1 or something like that. Set your DSL routers to use 192.168.101.x and 192.168.202.x to keep them on seperate networks.
- Copy Link
- Report Inappropriate Content
@Philbert Thanks for the detailed info
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 851
Replies: 4
Voters 0
No one has voted for it yet.