Home Network Community > All Threads > Setup lan to lan ipsec link with two TPlink Routers
< All Threads

Setup lan to lan ipsec link with two TPlink Routers

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Setup lan to lan ipsec link with two TPlink Routers

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Setup lan to lan ipsec link with two TPlink Routers
Setup lan to lan ipsec link with two TPlink Routers
2022-09-23 07:10:17 - last edited 2022-09-23 07:14:25
Model: TL-MR6400  
Hardware Version:
Firmware Version: 1.1.0 0.9.1 v0001.0 Build 210803 Rel.55933n

Hi there.

 

I would like to setup two LTE routers to link two home WAN's.

 

Router 1 is an MR6400 firmware 1.1.0 0.9.1 v0001.0 Build 210803 Rel.55933n

 

Router 2 is an MR600 firmware is 1.4.0 0.9.1 v0001.0 Build 211018 Rel.69149n

I had to install beta firmware as per https://community.tp-link.com/en/home/forum/topic/251514 so that I could get Ipsec back, (no ipsec on current firmwhere)

I setup both sides as per https://www.tp-link.com/za/support/faq/1661/ 

 

I have tried using tp link ddns cloud link as well as the actual IP addresses of each router.

 

Ipsec pass through is enabled but unsure if I need to open any ports.

 

No joy, both routers show "down" in the ipsec link page.

 

Any assistance most appreciated

 

Brent

  0      
 
  0      
 
#1
Options
1 Reply
Re:Setup lan to lan ipsec link with two TPlink Routers
2022-09-26 03:19:45

  @Citizen_Brent 

 

Hi, may I know if both routers are working on 3G/4G Router mode? and please check the WAN IP address of both of on Advanced->Status->Internet part to see if they are public IP address or private IP address.

 

In addition, for the MR6400 V5.20, please try to reinstall the firmware 210803, you could download the firmware from our official website:

https://www.tp-link.com/en/support/download/tl-mr6400/#Firmware

 

After that, if check if problem still exists.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 406

Replies: 1

Related Articles
IPsec VPN between two tplink 4G router
465 0
IPsec LAN-to-LAN between VR2800 and Draytek Router
402 0
Internet in LAN to LAN two routers setup drops after some minutes
543 0
How to configure IPSEC LAN to LAN VPN tunnel with TP-Link Archer MR200 and Cisco router
7008 1
LAN Setup
554 0
TPLINK (TL-MR6400) and ONEDRIVE LAN ERROR
1103 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.