ER605 and conncetions to the TP-Link Archer AX53

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER605 and conncetions to the TP-Link Archer AX53

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER605 and conncetions to the TP-Link Archer AX53
ER605 and conncetions to the TP-Link Archer AX53
2022-05-11 14:38:14 - last edited 2022-05-12 01:18:58
Model: Archer AX53  
Hardware Version: V7
Firmware Version: n/a

Hello I just need to know if this type of conncetion is possible

Thank you 

 

 

  0      
  0      
#1
Options
3 Reply
Re:ER605 and conncetions to the TP-Link Archer AX53
2022-05-12 16:02:43

  @Kaneco 

 

Yes, these connections make sense if the AX53 is in AP mode (Case 1). Otherwise you'll introduce quadruple NAT in your network.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  2  
  2  
#2
Options
Re:ER605 and conncetions to the TP-Link Archer AX53
2022-10-01 00:02:50

  @terziyski 

 

Hello I'm installing this Routers as mentioned before with a flowing ip address 

 

The omada router at first one with the ip address 192.168.2.1

 

And the others ax1600 ax53 with the following ip address fixed, all this Routers are installed as a access point, configured the same way, and with the DHCP server disable. Also with a separated WiFi networks for 2.4 and 5Ghz 

 

192.168.2.2

192.168.2.64

192.168.2.128

192.168.2.254

 

But the firts 2 Routers installed are with the led orange on the WAN/Internet connection 

 

And the last 2 Routers are with a green led for the wan/Internet connection 

 

This is strange... And now I'm facing a lot of issues with a disconnections from the network 

 

By the way I notice that I'm notified for a new fw on the page for the 2 last Routers in the list, that are working well. But no fw update are available for the other first 2 Routers... And the last ones disappeared from the network passing some time... 

 

I also tested with other network cable to avoid any problems form the cables... But the problem keeps.. 

 

Any one have a ideia what is going wrong with this? 

 

Thank you and best regards 

  0  
  0  
#3
Options
Re:ER605 and conncetions to the TP-Link Archer AX53
2022-10-02 01:32:34

  @Kaneco 

 

Orange LED on WAN interface means that you don't have an internet access on these particular AX53s.

And that's the reason you can't see the FW update available as on these particular AX53s.

If you have configured all four AX53s according to the guide I posted, they should work in an identical way.

This could usually happen due to a cabling problem. The easiest way to check that is to use a short factory made cable and test the four AX53s (one by one) connecting them to the ER605 LAN port and check if every one have an internet access (WAN interface LED green).

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 766

Replies: 3

Related Articles