Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > Only WiFi is working but ethernet ports are not

< All Threads

Only WiFi is working but ethernet ports are not

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Only WiFi is working but ethernet ports are not

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EnriqueW

2022-01-11 18:46:44 - last edited 2022-01-11 20:51:19

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-01-11

Only WiFi is working but ethernet ports are not

2022-01-11 18:46:44 - last edited 2022-01-11 20:51:19

Model: Archer C5400X

Hardware Version: V1

Firmware Version: 1.1.2 Build 20191223 rel.73956(5553)

I have problems using the Ethernet ports to connect to internet.

The interface shows 0 wired clients connected even though I have 3 wired devices connected.

WiFi is working fine.

I have no USB devices attached to the router.

I have tested the cables connecting my devices directly to my ISP router and all of them work fine.

I tried doing a factory reset and ethernet ports still won't work.

Wired clients is shown in 0 and Wireless clients is in 13 (which is correct)

If I scroll down to the ethernet connected devices it shows them correctly

Can you please help me troubleshoot this problem? It started happening just now, It was working fine before, I didn't change anything but it just stopped working

1 Reply

Kevin_Z

2022-01-20 08:06:07

Posts: 21584

Helpful: 5039

Solutions: 2543

Stories: 21

Registered: 2018-12-24

Re:Only WiFi is working but ethernet ports are not

2022-01-20 08:06:07

@EnriqueW

Hello, what are the devices connected to the LAN ports of the C5400X? Are they getting a valid IP address from the router? You can check that as per the guide below:

https://www.tp-link.com/support/faq/841/

If they can get valid IP addresses from the router, please do a simple ping test and see if the routing is good between them and the router LAN:

https://www.tp-link.com/support/faq/425/

If they cannot get a valid IP address from the router, you may try to manually assign the IP address on the wired devices, then check if they can talk to the router.

If none of the above helps, I'm afraid there might be a hardware issue with the LAN ports, you can contact the local tech support to be advised further:

https://www.tp-link.com/support/contact-technical-support/#Hotline-Support

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

EnriqueW

2022-01-11 18:46:44 - last edited 2022-01-11 20:51:19

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-01-11

Information

Helpful: 0

Replies: 1

Only WiFi is working but ethernet ports are not

Only WiFi is working but ethernet ports are not

Information

Voters 0

Tags