Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > does not show up as 802.11AC while configured in Master mode

< All Threads

does not show up as 802.11AC while configured in Master mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

does not show up as 802.11AC while configured in Master mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

tripac

2021-12-06 17:42:41 - last edited 2021-12-16 00:45:24

Posts: 2

Helpful: 2

Solutions: 0

Stories: 0

Registered: 2021-12-06

does not show up as 802.11AC while configured in Master mode

2021-12-06 17:42:41 - last edited 2021-12-16 00:45:24

Model: Archer T2U

Hardware Version: V3

Firmware Version:

Setup

----------

-h/w is a single board computer based on imx6 processor

-OS is Linux 4.9 (debian buster)

What is done

------------------

I used hostapd to configure T2U device as AP. The config file is setup for AC mode. AP gets created successfully.

When I run iwconfig command, it shows that Master mode with SSID (as in conf file) is created with a bit rate of about 450mbps

Problem

-----------------

IEEE 802.11 mode shows up as bgn rather than the expected 802.11AC.

1 Accepted Solution

Solla-topee

2021-12-07 01:48:25 - last edited 2021-12-16 00:45:24

Posts: 13724

Helpful: 2375

Solutions: 2074

Stories: 8

Registered: 2020-05-19

Re: does not show up as 802.11AC while configured in Master mode-Solution

2021-12-07 01:48:25 - last edited 2021-12-16 00:45:24

Hello @tripac

Archer T2U Wireless spec is (200 Mbps on 2.4GHz band and 433 Mbps on 5GHz band)

If the Wireless Link speed is around 433 Mbps, that is of 5Ghz band, not 2.4Ghz. It sounds a wrong display and should not affect the real speed.

How to check the associated/link speed on a wireless client

I hope that helps.

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.

Recommended Solution

2 Reply

Solla-topee

2021-12-07 01:48:25 - last edited 2021-12-16 00:45:24

Posts: 13724

Helpful: 2375

Solutions: 2074

Stories: 8

Registered: 2020-05-19

Re: does not show up as 802.11AC while configured in Master mode-Solution

2021-12-07 01:48:25 - last edited 2021-12-16 00:45:24

Hello @tripac

Archer T2U Wireless spec is (200 Mbps on 2.4GHz band and 433 Mbps on 5GHz band)

If the Wireless Link speed is around 433 Mbps, that is of 5Ghz band, not 2.4Ghz. It sounds a wrong display and should not affect the real speed.

How to check the associated/link speed on a wireless client

I hope that helps.

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.

Information

Helpful: 0

Replies: 2

does not show up as 802.11AC while configured in Master mode

does not show up as 802.11AC while configured in Master mode

Information

Voters 0

Tags