Home Network Community > All Threads > X20 and M4 roaming problem
< All Threads

X20 and M4 roaming problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

X20 and M4 roaming problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
X20 and M4 roaming problem
X20 and M4 roaming problem
2021-08-18 07:37:09 - last edited 2021-08-18 07:43:10
Model: Deco X20  
Hardware Version: V1
Firmware Version: 1.5.0 20210121 rel. 54794

I have two Deco X20 and borrowed M4R and M3W to test a third Deco with X20s.

 

Unfortunately there is a problem with roaming between WiFi 6 and WiFi 5 using Galaxy S21. When the phone connects to X20, it does not roam to M4 even if the WiFi signal is very weak, when I disable WiFi in the phone and it connects to M4, it is the opposite - roaming does not work to X20, the phone is connected all the time to M4.

 

This is not a Samsung fault because I have tested also X20s with M3W and roaming between them is perfect besides different WiFi standard. I have also tried to reset 3 times M4R and connect again, it did not help.

 

Is it anything I can do, or I need to buy another Deco?

  1      
 
  1      
 
#1
Options
4 Reply
Re:X20 and M4 roaming problem
2021-08-24 05:40:38

@sakul88 

For AP steering among different Deco nodes, only when the signal strength of the current AP (Deco) becomes lower than a threshold and the signal strength of another AP is good enough, Deco will recommend clients to roam via 802.11k/v standards.

 

For your case, it is a little bit different, Except for the Galaxy S21, did other devices behave the same?

 

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#2
Options
Re:X20 and M4 roaming problem
2021-08-24 06:34:27

@TP-Link

Devices without 802.11ax roam OK, I have also Samsung S21+ and Tab S7 - problem also exist, but those are similar devices. I will try on a Lenovo T14 (also 802.11ax) but I need to connect M4 again.

 

I understand that between 802.11ax and older standards roaming can be difficult, however with X20 and M3W it works flawlessly, so why shouldn't it with X20 and M4?

  0  
  0  
#3
Options
Re:X20 and M4 roaming problem
2021-10-13 10:44:26 - last edited 2021-10-13 10:45:07

@TP-Link

I have tested Lenovo T14 with 802.11ax and it is roaming properly between X20 and M4. It looks like, it's a Samsung problem. Do you have any ideas what could I do?

  0  
  0  
#4
Options
Re:X20 and M4 roaming problem
2021-10-20 07:07:45

@sakul88 

Hi, it is suggested you could turn off the Mesh Technology on the Deco APP for Samsung S21+ and Tab S7.

Turning off the Mesh Technology on the Samsung devices would not interfere with other mobile devices.

And if you have enabled the private MAC address, you could also turn it off to test the connection.

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#5
Options

Information

Helpful: 1

Views: 1338

Replies: 4

Related Articles
Deco X20 4G connection problem
374 0
Moving from Deco M4 to X20
1649 0
Problem with one of the Deco X20
562 0
X20 wireless network problem
360 0
problem to add more decos x20
786 0
Deco X20 vs. Deco M4: Which Setup is Best for Extending My WiFi?
1413 2
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.