Archer VR600v Power LED blicking - no other lights

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR600v Power LED blicking - no other lights

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer VR600v Power LED blicking - no other lights
Archer VR600v Power LED blicking - no other lights
2021-02-15 00:45:48 - last edited 2021-02-19 01:40:28
Model: Archer VR600v  
Hardware Version:
Firmware Version:

Purchased July 2019 this was working fine until today when both wired and WiFi connections suddenly stopped working.

 

Power LED was on and blinking but all other lights are out.

 

NO CHANGES to router config for MANY months so this is NOT a problem created by myself.

 

Searched forums and support and solutions are no tthere.

 

Clearly TP-Link have a quality problem as there and 1000's of people reporting this same issue across a variety of devices.

 

My back-up router is 20 years old and still going strong....

 

when are you going to start making products that actually last as long as people expect(hope)?

 

 

  0      
  0      
#1
Options
1 Accepted Solution
Re:Archer VR600v Power LED blicking - no other lights-Solution
2021-02-16 00:57:30 - last edited 2021-02-19 01:40:28

@Kevin_Z I plugged the router back in after it sat unpowered for about 8 hrs. 

 

Started up no problems and has now been sitting on my desk running for around 15hrs without an issue.  I am running a few devices on both 2.4 and 5g WiFi as an access point so that I can see if any dropouts.

 

Clearly something strange happened yesterday but good to know I have 3yr warranty on this.  I will leave running on my desk until weekend and then connect back up to the internet.

 

Recommended Solution
  1  
  1  
#5
Options
5 Reply
Re:Archer VR600v Power LED blicking - no other lights
2021-02-15 02:39:55 - last edited 2021-02-15 07:42:53

@millesm 

 

As per your user manual :

 

Try to hard reset the device (Method 1) to see if it will start up normally.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Archer VR600v Power LED blicking - no other lights
2021-02-15 05:31:15 - last edited 2021-02-15 07:42:53

Yes, I have seen that in the manual but typically the startup phase only took a few mins and I have not done a firmware upgrade, it just stopped of it's own accord.

 

When router stopped working, after a power cycle, the flashing light stays on for 30 odd mins.

 

Factory reset button did nothing to resolve. 30/30/30 reset steps I found on the net did not help either.

 

Powered off and let it sit for 10+ mins then tried again and flashing went on for at least 15 mins before I disconnected and switched to old router.

 

Currently sitting powered off for 1/2 day so will retry again tonight.

  0  
  0  
#3
Options
Re:Archer VR600v Power LED blicking - no other lights
2021-02-15 07:47:51

@millesm 

Hi,

Is everything going on well now?

If still the same, since the warranty service covered for three years in Australia, please try to contact the local support team to check for warranty service.

Thank you very much.

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Archer VR600v Power LED blicking - no other lights-Solution
2021-02-16 00:57:30 - last edited 2021-02-19 01:40:28

@Kevin_Z I plugged the router back in after it sat unpowered for about 8 hrs. 

 

Started up no problems and has now been sitting on my desk running for around 15hrs without an issue.  I am running a few devices on both 2.4 and 5g WiFi as an access point so that I can see if any dropouts.

 

Clearly something strange happened yesterday but good to know I have 3yr warranty on this.  I will leave running on my desk until weekend and then connect back up to the internet.

 

Recommended Solution
  1  
  1  
#5
Options
Re:Archer VR600v Power LED blicking - no other lights
2021-02-19 01:40:22

@millesm 

 

Good to know that, please monitor the performance then, just let us know if you still have an issue.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1252

Replies: 5

Related Articles