Archer VR400 Modem Mode/Transparent Bridging Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR400 Modem Mode/Transparent Bridging Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer VR400 Modem Mode/Transparent Bridging Mode
Archer VR400 Modem Mode/Transparent Bridging Mode
2020-02-18 15:48:20 - last edited 2020-02-20 08:07:47
Model: Archer VR400  
Hardware Version: V1
Firmware Version: 0.1.0 0.9.1 v0070.0 Build 160613 Rel.40404n

Hello.
I am looking for a way to switch into Modem Mode/Transparent Bridging Mode so i can use anoter router.
My second router is Ethernet WAN and much better and this one is having overheating issues when being pushed.
If this is not possible is there another Modem out there that i can use ? (I do not want a Router/ISR/AP/etc. just the modem, as the router i am using has dd-wrt and i need a public address on the WAN port to enable a 6in4 tunnel).

Thanks.

  0      
  0      
#1
Options
1 Accepted Solution
Re:Archer VR400 Modem Mode/Transparent Bridging Mode-Solution
2020-02-20 08:00:22 - last edited 2020-02-20 08:07:47

@AceScottie 

 

Hello, the Archer VR400 works in bridge mode by default; so you can hard reset it by holding the reset button for 10s with it powered on.

 

Then you can connect the second router to it and configure it as the main router. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Archer VR400 Modem Mode/Transparent Bridging Mode-Solution
2020-02-20 08:00:22 - last edited 2020-02-20 08:07:47

@AceScottie 

 

Hello, the Archer VR400 works in bridge mode by default; so you can hard reset it by holding the reset button for 10s with it powered on.

 

Then you can connect the second router to it and configure it as the main router. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 5444

Replies: 1

Related Articles