Home Network Community > All Threads > "Integration" between TP-link Wi-Fi Routers and Deco (P9)
< All Threads

"Integration" between TP-link Wi-Fi Routers and Deco (P9)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

"Integration" between TP-link Wi-Fi Routers and Deco (P9)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
"Integration" between TP-link Wi-Fi Routers and Deco (P9)
"Integration" between TP-link Wi-Fi Routers and Deco (P9)
2020-01-02 10:46:45 - last edited 2020-02-24 12:03:00

I recently purchased a set of TP-Link Deco P9's as a means of providing extended Wi-Fi connectivity throughout my home.

 

However, the P9 (and it seems most Deco kit) is simply a router, with no modem funcationality.

 

I'm very unhappy with the supplied BT Smart Hhub provided by a leading UK ISP. Infact, i'm not a fan of IP supplied modem-routers as theyre often very limited in functionality and configurability.

 

I'm considering perhaps buying a TP-Link VDSL Wi-Fi router to replace the BT Smart Hub, but I have a question in relation to "integration" workability with Deco units. Is there any thing to take into consideration? If needed, i'd obviously most likely disable the Wi-Fi on the modem-router in favour of the Deco, but again i'm thinking there might be some integration functionality between two TP-link systems?

 

Any ideas/suggestions would be appreciated.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:"Integration" between TP-link Wi-Fi Routers and Deco (P9)-Solution
2020-01-07 09:03:11 - last edited 2020-02-24 12:03:00

@Salem874 

 

Hello, below are some VDSL modem routers.

https://www.tp-link.com/uk/home-networking/dsl-modem-router/?filterby=4882 

 

First, you can use the VDSL modem router as bridge mode and the Deco P9 works in regular router mode and acts as the DHCP server. Like ISP--VDSL modem router( bridge mode)--Main Deco( router mode) ---/)))(((/PLC slave Deco P9.

 

Or you can use VDSL modem router as the regular router mode and the Deco P9 as the access point to avoid the double NAT issue. 

 

Otherwise you can use both as regular router, then there will be two separate networks; the devices connected to the VDSL router cannot access the devices which connected to the Deco P9.

 

You can refer to the faq below to get the difference between router mode and AP mode. 

https://www.tp-link.com/support/faq/2399/ 

https://www.tp-link.com/support/faq/2420/

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:"Integration" between TP-link Wi-Fi Routers and Deco (P9)-Solution
2020-01-07 09:03:11 - last edited 2020-02-24 12:03:00

@Salem874 

 

Hello, below are some VDSL modem routers.

https://www.tp-link.com/uk/home-networking/dsl-modem-router/?filterby=4882 

 

First, you can use the VDSL modem router as bridge mode and the Deco P9 works in regular router mode and acts as the DHCP server. Like ISP--VDSL modem router( bridge mode)--Main Deco( router mode) ---/)))(((/PLC slave Deco P9.

 

Or you can use VDSL modem router as the regular router mode and the Deco P9 as the access point to avoid the double NAT issue. 

 

Otherwise you can use both as regular router, then there will be two separate networks; the devices connected to the VDSL router cannot access the devices which connected to the Deco P9.

 

You can refer to the faq below to get the difference between router mode and AP mode. 

https://www.tp-link.com/support/faq/2399/ 

https://www.tp-link.com/support/faq/2420/

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 3857

Replies: 1

Related Articles
TP-Link 5G router ArcherNX200 has no easyMesh integration with TP-Link RE305 (WPA3)
252 1
Question about tp-link routers
822 0
tp-link wifi routers pinging tp-link.com
1529 0
How to replace / return TP-Link Routers
577 0
VPN Clients on TP-Link Routers
46805 8
What is DoH and How to use it on TP-Link Wi-Fi Routers?
8929 6
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.